Full Judgment Text
Text read from the judgment PDF published on the High Court's eCourts portal, through the
Indian High Court Judgments open data set (Dattam Labs,
CC BY 4.0).
The court's own copy is the authoritative text.
*
IN THE HIGH COURT OF DELHI AT NEW DELHI
Date of Decision: 10th September, 2026
%
#
CNR No. DLHC010418402025
+
C.A.(COMM.IPD-PAT) 24/2025 and I.A. 7074/2026
ITC LIMITED
.....Appellant
Through: Mr. J. Sai Deepak, Senior Advocate
with Ms. Amrita Majumdar, Mr. Samik
Mukherjee, Ms. Kritika Kaur and Mr. Avinash K.
Sharma, Advocates.
versus
PHILIP MORRIS PRODUCTS S.A. & ORS.
.....Respondents
Through: Mr. Sanjeev Tiwari, Mr. Manish
Aryan, Mr. Nishant Rai and Ms. Yojana
Sonkvsare, Advocates for R-1.
Ms. Nidhi Raman, CGSC with Mr. Om Ram and
Ms. Nikita Singh, Advocates for R-2 and R-3.
#
CNR No. DLHC010220082025
+
W.P.(C)-IPD 25/2025 and C.Ms. 102-103/2025 & 69/2026
ITC LIMITED
.....Petitioner
Through: Mr. J. Sai Deepak, Senior Advocate
with Ms. Amrita Majumdar, Mr. Samik
Mukherjee, Ms. Kritika Kaur and Mr. Avinash K.
Sharma, Advocates.
versus
THE ASSISTANT CONTROLLER OF PATENTS AND DESIGNS
& ORS.
.....Respondents
Through: Ms. Nidhi Raman, CGSC with Mr.
Om Ram and Ms. Nikita Singh, Advocates for R-1
and R-2.
Mr. Sanjeev Tiwari, Mr. Manish Aryan, Mr.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
Nishant Rai and Ms. Yojana Sonkvsare, Advocates
for R-3.
CORAM:
HON'BLE MS. JUSTICE JYOTI SINGH
JUDGEMENT
JYOTI SINGH, J.
1.
This judgment disposes the writ petition and the Appeal filed by the
Appellant, challenging two orders, both dated 30.01.2025. In the writ
petition filed under Article 226 of the Constitution of India, challenge is laid
to the order whereby two Interlocutory Petitions (‘IPs’) have been dismissed
as also order dismissing the post-grant opposition of the Appellant. In the
appeal filed under Section 117A of The Patents Act, 1970 (‘1970 Act’),
order rejecting the post-grant opposition is challenged. For the sake of
convenience and uniformity, ITC Limited is hereinafter referred to as the
Appellant; Philip Morris Products as Patentee and Controller of Patents &
Designs as the Controller.
2.
Case of the Appellant, to the extent necessary, is that Appellant is an
Indian conglomerate company operating in India for more than 100 years
and has diversified presence in Fast Moving Consumer Goods (‘FMCG’)
sector with branded packaged foods, personal care products, education and
stationery products, agarbattis and safety matches, cigarettes and cigars, as
well as in other businesses such as hotels, paperboards and specialty papers,
packaging, agri-business, information technology etc. Appellant is a market
leader in manufacturing and sale of cigarettes in India and is also engaged in
the research and development of cigarettes and tobacco products with access
to latest technologies in manufacture of cigarettes. Patentee is located in
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
Neuchâtel, L, Switzerland and the patent granted in its favour was
opposed by the Appellant in post-grant opposition under Section 25(2) of
1970 Act.
3.
Instant proceedings relate to an invention titled “HEATED AEROSOL
GENERATING ARTICLE WITH THERMAL SPREADING WRAP”, in
respect of which patent was granted in favour of the Patentee on 14.12.2021.
Patent Application was filed as a National Phase Application bearing no.
201617018958 with nationalization date being 02.06.2016, claiming priority
from Priority Application EP13195877.9 filed on 05.12.2013 and term of the
patent expires on 04.12.2034. The prosecution details of IN’384250
(IN’250) are as follows:-
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
4.
It is stated that Appellant filed post-grant opposition under Section
25(2) of 1970 Act read with Rule 57 of the Patents Rules, 2003 (‘2003
Rules’) objecting on grounds of ‘lack of novelty’ under Section 25(2)(b);
‘prior use/prior knowledge’ under Section 25(2)(d); ‘lack of inventive step’
under Section 25(2)(e); ‘insufficiency of disclosure’ under Section 25(2)(g);
and ‘not an invention’ under Section 25(2)(f). Prior arts D1 to D6 were cited
by the Appellant in the written statement of Opposition and additional
documents D7 to D10 were cited under Rule 62(4) of 2003 Rules on
31.05.2024. The prior art documents are as follows:i.
US2010200006A1 entitled “Tobacco-Containing Smoking
Article” published on 12.08.2010, referred to as “Dl”.
ii.
EP2486812A1 entitled “Smoking article” published on
15.08.2012 referred to as “D2”.
iii.
US5551451A entitled “Fuel element composition” published
on 03.09.1996, referred to as “D3”.
iv.
US4955397A entitled “Cigarette” published on 11.09.1990,
referred to as “D4”.
v.
EP0174645A2 entitled “Smoking article” published on
19.03.1986, referred to as “D5”.
vi.
EP2552246A2 entitled “Smoking Article With Heat Resistant
Sheet Material” published on 06.02.2013, referred to as “D6”.
vii.
US20110192408A1 titled “Non-combustion flavor inhalation
article” published on 11.08.2011, referred to as “D7”.
viii. US6129087A titled “Reduced ignition propensity smoking
articles” published on 10.10.2000, referred to as “D8”.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
ix.
US20090320865A1 titled “Flame-retardant and Fireproof
Cigarette” published on 31.12.2009, referred to as “D9”.
x.
US2718889A titled “Heat absorbing and transferring band for
cigarettes” published on 27.09.1955, referred to as “D10”.
5.
It is stated that reply statement was filed by the Patentee on
17.02.2023 and the post-grant opposition was heard on 06.06.2024,
whereafter both parties filed written submissions on 21.06.2024. Patentee
filed two auxiliary claim sets along with written submissions, which were in
addition to existing claims and not proposed at the hearing on 06.06.2024.
Objection was raised by the Appellant vide letters dated 22.07.2024 and
26.07.2024 and thereafter Interlocutory Petition (‘IP') dated 14.08.2024 was
filed. Meanwhile, on 25.07.2024, Controller issued notice to the parties for
re-hearing on 20.08.2024, but there was no clarity on the claims which the
Patentee intended to pursue.
6.
It is stated that ultimately Patentee did not pursue the amendment
sought and instead filed fresh written submissions in respect of existing
granted claims on 04.09.2024, making submissions beyond reply statement
and earlier written submissions. In light of this, second IP dated 21.09.2024
was filed by the Appellant seeking rejection of the fresh written
submissions. However, vide order dated 30.01.2025, both the IPs were
dismissed and on the same day, by a separate order, post-grant opposition
was also rejected by the Controller. Appellant filed the present writ petition
challenging both orders as also the appeal, separately and substantively
challenging rejection of the post-grant opposition as also seeking revocation
of IN’250 in entirety. Before proceeding further, it will be relevant to extract
hereunder, the granted set of claims:-
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
“1. A heated aerosol-generating article (1000, 2000) for use with an
electrically-operated aerosol-generating device (3010) comprising a
heating element (3100), the aerosol-generating article (1000, 2000)
comprising:
an aerosol-forming substrate (1020, 2020) radially encircled by a
sheet of thermally-conductive material (1222, 2222), in which the aerosolforming substrate (1020, 2020) comprises a gathered sheet of aerosolforming material circumscribed by a wrapper (5060), the wrapper (5060)
being the sheet of thermally-conductive material which acts as a
thermally-conducting flame barrier for spreading heat and mitigating
against the risk of a user igniting the aerosol-forming substrate (1020,
2020) by applying a flame to the aerosol-generating article (1000, 2000).
2. The heated aerosol-generating article (1000) as claimed in claim 1,
wherein the aerosol-generating article (1000) comprises a plurality of
elements (1020, 1030, 1040, 1050), including the aerosol-forming
substrate (1020), assembled within a cigarette paper (1060) to form a rod,
the sheet of thermally-conductive material (1222) being located within the
cigarette paper (1060).
3. The heated aerosol-generating article (2000) as claimed in claim 1,
wherein the aerosol-generating article (2000) comprises a plurality of
elements (2020, 2030, 2040, 2050), including the aerosol-forming
substrate (2020), assembled within a cigarette paper (2060) to form a rod,
the sheet of thermally-conductive material (2222) being located radially
external to the cigarette paper (2060).
4. The heated aerosol-generating article (1000, 2000) as claimed in claim
1, wherein the aerosol -generating article (1000, 2000) is in the form of a
rod having a mouth end (1012, 2012) and a distal end (1013, 2013)
upstream from the mouth end (1012, 2012), in which a portion of the
thermally-conductive material (1222, 2222) covers the distal end (1013,
2013) of the rod.
5. The heated aerosol-generating article (1000) as claimed in claim 1,
wherein the aerosol-generating article (1000) is in the form of a rod
having a mouth end (1012) and a distal end (1013) upstream from the
mouth end (1012), in which a spacer element (1040) is located within the
rod upstream of the aerosol-forming substrate (1020).
6. The heated aerosol-generating article (1000) as claimed in claim 1,
wherein the aerosol-generating article (1000) is in the form of a rod
having a mouth end (1012) and a distal end (1013) upstream from the
mouth end (1012), in which the aerosol-forming substrate (1020) is
located at the distal end (1013) of the rod.
7. The heated aerosol-generating article (1000, 2000) as claimed in claim
1, wherein the sheet of thermally-conductive material is or comprises
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
metal foil.
8. The heated aerosol-generating article (1000, 2000) as claimed in claim
7, wherein the sheet of thermally conductive material is a sheet of material
formed by co-lamination of metal foil with paper, or a sheet material
formed by co-lamination of metal foil with reconstituted tobacco.
9. The heated aerosol-generating article (1000, 2000) as claimed in claim
7, wherein the metal foil is aluminium foil (1222, 2222).
10. The heated aerosol-generating article (1000, 2000) as claimed in
claim 1, for use with an aerosol-generating device (3010) comprising an
insertable heating element (3100) for insertion into a distal end (1013,
2013) of the heated aerosol generating article (1000, 2000).”
ARGUMENTS IN WRIT PETITION:
Submissions on behalf of the Appellant
7.
As per the specifications of IN’250, the problem to be solved is to
reduce the propensity of ignition of aerosol-generating articles by using a
wrapper circumscribing the gathered sheet of aerosol-forming material,
which may be a metal foil or may comprise a metal foil, e.g., the wrapper
may be aluminium foil or a coal laminated sheet comprising a layer of
aluminium foil. Therefore, as per the Patentee, the technical advancement is
that the wrapper of thermally conductive material circumscribing the
gathered sheet of aerosol-forming material helps to reduce the likelihood of
ignition of the aerosol-forming substrate of the heated aerosol-generating
article, if a user chooses to light up the article like a conventional cigarette
applying flame. As per the claims specification, if a user was to apply flame
to the article, the thermally conductive material would conduct heat away
from the point of application with the flame, thereby reducing likelihood of
ignition of substrate material. Thus, when a user applies flame to such a rod
forming part of heated aerosol-generating article, he may experience
difficulty in igniting the heated aerosol-material and may therefore be
discouraged from smoking in an unintended way. Claim 1 is an independent
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
claim directed at ‘A heated aerosol-generating article’ and Claims 2-10 are
directly or indirectly dependent on Claim 1.
8.
The controversy started with the Patentee filing two sets of auxiliary
claim amendments with written submissions dated 21.06.2024, recognizing
the inherent weakness of its case. Controller ought to have disregarded the
auxiliary claims’ amendment sought in light of Interlocutory Petition dated
14.08.2024 (IP-1) filed by the Appellant, however, notice was issued to both
parties on 06.06.2024 to file their written submissions, which they did.
Appellant sent two letters dated 22.07.2024 and 26.07.2024 objecting to a
re-hearing once proceedings in the post-grant opposition were concluded on
06.06.2024, in which parties were directed to file their written submissions
as also to understand the purpose of scheduling a fresh hearing on
20.08.2024, but to no avail. This procedure is unknown to law and the only
remedy available to the Patentee was to file an application for leave to
amend and follow the procedure laid down in Rule 81(3)(a) (b) and (c) of
2003 Rules, having regard to the provisions of Section 57(3) of 1970 Act,
which he did not follow. Controller thus erred in permitting re-hearing after
conclusion of hearing on post-grant opposition.
9.
Rule 62(5) of 2003 Rules categorically provides that Controller shall
hear the parties, decide the opposition and notify its decision to the parties
after giving reasons thereof. Proposing amendments to the claims without
application in the prescribed manner along with prescribed fee is contrary to
the statutory scheme. It is only the Controller who can amend the claims
under Section 25(4) and it is not open to a patentee to seek voluntary
amendment without an application under Section 57(3) of 1970 Act. Despite
these anomalies, Controller proceeded to hold a hearing on 20.08.2025.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
10.
On the day of scheduled hearing, Appellant was not allowed to
address arguments on IP-1 while the Controller indulged the Patentee by
permitting filing of fresh written submissions to defend the auxiliary claims.
Importantly, Patentee gave no indication whether it would pursue the
amendment or defend the existing claims and resultantly, it was not clear to
the Appellant whether opposition would be decided on granted claims on
record or on the auxiliary claim amendments and in fact, Appellant was
under the bona fide impression that IP-1 will be first heard on this issue.
While traversing the fresh written submissions, Appellant found that the
contents were beyond the earlier written submissions dated 21.06.2024, oral
submissions made on 20.08.2024 and pleadings of the Patentee in reply
statement, more particularly, paragraphs 56 and 57, which triggered the
filing of Interlocutory Petition dated 21.09.2024 (IP-2) to strike off the fresh
written submissions. Both IP-1 and IP-2 were erroneously dismissed by the
Controller vide order dated 30.01.2025 and that too, treating both as relating
to auxiliary claim amendments, overlooking that IP-2 was for striking off
the fresh written submissions.
11.
Disadvantage and prejudice suffered by the Appellant owing to
fresh written submissions, is not merely procedural. Reading of
impugned order dated 30.01.2025, whereby post-grant opposition was
rejected, shows that Controller’s decision is substantially based on the
fresh written submissions and that too without providing an opportunity to
the Appellant to respond to them, which violates principles of natural
justice. Two observations in the impugned order are based entirely on the
fresh written submissions and have prejudiced the Appellant and are as
follows:-
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
12.
Admittedly, Patentee did not press the auxiliary claims’ amendment in
the hearing held on 20.08.2024 and restricted its case to the granted claims
and thus only IP-2 was to be decided. However, the Controller mechanically
dismissed both the IPs treating them as those directed against auxiliary
claims. Since there was gross violation of principles of natural justice and
procedure, writ jurisdiction of this Court was rightly invoked in addition to
challenging the order rejecting the post-grant opposition on merits and is
maintainable. Moreover, the order rejecting the IPs is not an ‘order’ under
Section 25(4) against which an appeal lies under Section 117A of 1970 Act.
13.
It is trite that writ petition is ordinarily not maintainable when an
efficacious alternate remedy is available. Arguendo, even if the remedy of
appeal was available and writ petition has been filed, both the appeal and the
writ petition are being heard together and therefore, no prejudice is caused to
the Patentee. In fact, if the writ petition is allowed, it will obviate the need of
a merit based detailed adjudication by the Court. The objection on
maintainability of the appeal overlooks the settled law that if there are
violations of principles of natural justice, then existence of alternate remedy
does not act as a bar. [Ref.: Whirlpool Corporation v. Registrar of Trade
Marks, Mumbai and Others, (1998) 8 SCC 1 and Best Agrolife Limited v.
Deputy Controller of Patents and Another, 2022 SCC OnLine Del 1982].
Patentee’s and Controller’s argument that IPs form part of the same
opposition proceedings and therefore, the decision on the IPs is also a
decision under Section 25(4) and hence the only remedy is an appeal, is
legally flawed since under Section 25(4), Controller can only maintain,
amend or revoke the patent, whereas the prayers in the two IPs were to reject
the auxiliary claim amendments and strike off the fresh written submissions,
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
respectively, which is not within the purview of Section 25(4).
14.
Argument of the Respondents that Controller can always consider
new pleadings or written submissions while passing an order under Section
25(4) is contrary to the judgment of the Supreme Court in Shivaji Balaram
Haibatti v. Avinash Maruthi Pawar, (2018) 11 SCC 652, holding that
parties cannot travel beyond pleadings. Purpose of pleadings is to ensure
that litigants come to trial with all issues clearly defined, as held by the
Supreme Court in Bachhaj Nahar v. Nilima Mandal and Another, (2008)
17 SCC 491.
Submissions on behalf of the Controller
15.
The writ petition is not maintainable and be dismissed without
going into merits. Impugned orders were passed under Section 25(4) and
Section 117A(2) explicitly provides for an appeal challenging any decision,
order or direction of the Controller. Further, there were no extraordinary
circumstances or compelling reasons, justifying invoking the writ
jurisdiction of this Court. Entertaining this writ petition would set a
dangerous precedent where parties will choose to file a writ petition or an
appeal at their option, which will violate the statutory scheme and result in a
situation never intended by the legislature. In any case, there is no provision
in the 1970 Act, which provides for filing interlocutory petitions in postgrant opposition proceedings and this was a wrong path that the Appellant
chose on its own volition. Appellant could only have challenged the final
order rejecting the post-grant opposition.
16.
Impugned order dismissing the IPs arises out of the same opposition
proceedings and cannot be separately challenged. In fact, filing of the IPs
was itself misconceived as there is no provision under the 1970 Act
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
envisaging filing of interlocutory petitions by an opponent at the post-grant
opposition stage. Appellant artificially and erroneously bifurcates a
consolidated statutory proceeding into two segments. Section 117A(2)
explicitly permits a statutory appeal against the ‘final’ order passed under
Section 25(4) and Legislature has consciously and deliberately omitted any
reference to interim or interlocutory orders passed during the pendency of
the opposition. An appeal has a wider scope and in the instant case, the
appeal takes within its sweep challenge to procedural violations, if any, as
also alleged violations of principles of natural justice. Extraordinary writ
jurisdiction should not be used as appellate jurisdiction to correct procedural
orders or interlocutory dismissals by statutory authorities.
17.
Without prejudice, even on merits the Appellant has no case. There
was no violation of any procedure or principles of natural justice. Appellant
was granted ample opportunities to rebut patentee’s fresh written
submissions after conclusion of each hearing. After the post-grant
opposition was heard on 06.06.2024, Appellant filed written submissions on
21.06.2024 and Patentee filed its written submissions on the same day with
two auxiliary claim sets. Appellant filed IP-1 on 14.08.2024 opposing the
amendment post-conclusion of the hearing of the post-grant opposition. On
20.08.2024, hearing was conducted which was duly attended on behalf of
the Appellant and on 21.09.2024, IP-2 was filed for striking off fresh written
submissions. Hearing was scheduled for 29.10.2024, but Appellant sought
adjournment and hearing was adjourned to 21.11.2024, on which date the
Appellant was heard. On the same day rejoinder was filed by the Appellant,
followed by post-hearing submissions on 06.12.2024 and thus it cannot be
asserted that opportunity of hearing was denied. In any case, once the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
Patentee gave up the amendments sought and decided to restrict its case to
the granted claims on record, there was no prejudice caused to the
Appellant. The argument that the impugned order is based on and influenced
by the pleas in the fresh written submissions, is misconceived. The
impugned decision is well-reasoned and taken after considering inter alia
the prior arts cited, respective submissions of the parties, both factual and
legal, claims specifications and recommendations of the Opposition Board,
which is self-explicit from a plain reading of the order.
Submissions on behalf of the Patentee
18.
Post-grant opposition proceedings are governed by Section 25(2) and
25(6) of the 1970 Act read with Rules 55A to 62 of the 2003 Rules and there
is no provision in either, envisaging filing of written submissions or IPs and
yet the Controller afforded opportunity to both parties to file written
submissions and also entertained Appellant’s IPs. Writ petition is an abuse
of process of law since Patentee did not take steps to add the auxiliary claim
sets under Section 57(3), after the advice of the Controller in this regard and
hence, IP-1 was rendered infructuous and rightly dismissed. Both sides were
afforded opportunity of hearing before the post-grant opposition was
rejected by a separate and detailed speaking order and only because the
outcome was not favourable to the Appellant, objection of violation of
principles of natural justice is being raised. The impugned orders were
passed after careful consideration of the granted claims and objections raised
and after filing the Appeal laying a substantive challenge to these orders,
Appellant cannot pursue the writ petition as a parallel proceeding. The
contents of the fresh written submissions were not new or outside the earlier
pleadings and in fact the distinction in metal foil and laminate is found in the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
complete claims specifications itself and was only explained in the written
submissions for the benefit of the Controller, owing to the points brought out
by the Appellant in the post-grant opposition.
ARGUMENTS IN APPEAL:
Submissions on behalf of the Appellant
19.
Appeal lays a challenge to order dated 30.01.2025 passed by the
Controller under Section 25(4) of 1970 Act rejecting the post-grant
opposition filed by the Appellant in respect of IN’250 granted in favour of
the Patentee. Impugned patent IN’250 relates to heated aerosol generating
article for use with an electrically operated aerosol-generating device
comprising a heating element, the aerosol-generating article comprising an
aerosol-forming substrate radially encircled by a sheet of thermally
conductive material and as claimed, the problem it resolves is reduction in
the propensity of ignition of aerosol-generating articles by using a wrapper
circumscribing the gathered sheet of aerosol-forming material, which may
be a metal foil or may comprise of a metal foil e.g. aluminium foil or a
co-laminated sheet comprising a layer of aluminium foil. The patent
comprises a set of 10 claims, where Claim 1 is an independent claim and
Claims 2-10 are directly or indirectly dependent on Claim 1. Appellant filed
a post-grant opposition under Section 25(2) of the 1970 Act, since the
granted patent lacks novelty in view of prior arts D1 and D7 under Section
25(2)(b); lacks prior use/prior knowledge under Section 25(2)(d); lacks
inventive step under Section 25(2)(e); is not an invention under
Section 25(2)(f) and there is insufficiency of disclosure under Section
25(2)(g), however, the same has been dismissed erroneously by the
Controller.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
20.
Prior art D1 discloses a smoking article incorporated within an
electrically powered aerosol-generating device comprising a heating element
for forming thermally generated aerosol incorporating components of
tobacco and thus, destroys novelty by anticipating all elements of Claim 1.
D1 teaches that the tobacco rod can be wrapped in conventionally known
wrapping materials like paper and metal foil. Figure 2 of D1 shows that the
tobacco rod is wholly circumscribed by a wrapping material composed of
laminate of metallic foil and paper. D1 also discloses aerosol-forming
substrate comprising a gathered sheet of aerosol-forming material. The
feature claimed to be novel and inventive is the thermally conductive
material acting as a flame barrier for spreading heat and mitigating
against the risk of a user igniting the aerosol-forming substrate by applying
flame to the aerosol-generating article, is merely a functional feature and
inherent to such metal foil wrappers and thus Patentee has made no
contribution to the art.
21.
Controller erred in holding that the patent is novel over D1,
overlooking that all features of Claim 1 are disclosed in D1. Even the
Opposition Board erred inasmuch as after acknowledging that D1 discloses
all features of Claim 1 viz., (a) aerosol-forming substrate comprising a
gathered sheet of aerosol-forming material; and (b) aerosol-forming
substrate radially encircled by a sheet of thermally conductive material i.e.
metallic foil taught in D1, it held that the invention was novel, solely relying
on thermal conductivity feature, which is only a functional aspect.
22.
Prior art D7 is also a novelty destroying prior art, which anticipates all
elements of independent Claim 1 of the patent. D7 relates to a heated
aerosol-generating article for use with an electrically operated aerosol-
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
generating device and teaches that the tobacco rod is wrapped in wrapping
material made of aluminium foil. Figure 3 of D7, illustrates that the tobacco
sheet is wholly circumscribed by a wrapping material made of aluminium
foil. D7 discloses aerosol-forming substrate comprising a tobacco sheet and
describes wounding of multiple layers in para [0034], which is equivalent to
concept of gathered sheets, since ‘wounding of multiple layers’ is a type of
gathering which happens in a structured way. D7 also teaches that the
wrapper can be a metal foil with high thermal conductivity such as
aluminium foil [para 0084] and the desire to avoid confusion of tobacco
sheet [para 0004 to 0009]. D7 also teaches that aluminium foil has high heat
conductivity in the range of 236W/m.K. Patentee has simply worded
Claim 1 in a manner that it appears novel, but actually there resides no
novelty in this feature and the claim is entirely anticipated by D7.
23.
Granted patent also lacks obviousness/lack of inventive step and D1 is
the closest prior art, disclosing a smoking article incorporated within an
electrically powered aerosol-generating device and a wrapping material as a
laminate of metallic foil and paper. Arguendo, even if the flame barrier
function/property of the thermally conducting material is not explicitly
disclosed in D1, it would be obvious to a person skilled in the art to expect
such wrappers to act as flame barriers, as this is an inherent property of such
thermally conducting materials. D7 also destroys the obviousness of the
patent as it relates to a heated aerosol-generating article for use with an
‘electrically’ operated aerosol-generating device and Figure 3 of D7 teaches
a roll including a tobacco sheet, where the roll is obtained by wrapping the
outside of the hollow cylindrical shaped tobacco sheet with a heat
conductive rapid material. D7 teaches that wrapper can be a metal foil with
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
high thermal conductivity such as aluminium foil and the desire to avoid
combustion of tobacco sheet. A person skilled in the art knows that materials
with high thermal conductivity such as aluminium foil are capable of
spreading/conducting heat easily and are not easy to ignite as they have a
high ignition temperature. Person skilled in the art would obviously know
that a metal/aluminium foil can be used as a barrier to spread heat and
mitigate the risk of ignition if flame is applied to the substrate. Furthermore,
para [0034] describes a wounded sheet of tobacco, which is equivalent to a
gathered sheet, another feature, which according to the Patentee is inventive
in the granted patent.
24.
D1 in combination with D3, which teaches metal/aluminium foil
laminate as a wrapper for encircling the aerosol-generating substrate and its
use for preventing excessive combustion, makes the claims in the patent
obvious. Although D2 does not explicitly disclose that the smoking article is
used with an electrically operated device as also the thermally conducting
flame barrier, however, feature of flame barrier is inherent in the disclosed
wrapper and person skilled in the art can use the disclosed article without
any modification to reach the claimed invention. There resides no
inventiveness in using a thermally conductive wrapper known to conduct
heat to encircle the tobacco rod as use of such wrappers was known in the
art and is in fact disclosed in D1 and D2.
25.
D5, similar to D4’s teaching, teaches a smoking article, which utilizes
a combustible fuel element, preferably of a carbonaceous material, in
conjunction with a physically separate aerosol-generating means that is in
conductive heat exchange relationship with the fuel element, which is about
20mm long and as disclosed in paras [0020 and 0021], the foil lined paper
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
tube at the mouth end piece of the article surrounds aerosol-generating
means and the rear non-lighting end of fuel element. This increases the heat
transfer to the aerosol generator and the foil helps to extinguish the fire
cone. Therefore, patentee has merely put to use a well-known property of
metallic foils, which is known to have high thermal conductivities. The
problem to be solved was to prevent an unintended use i.e., accidental
ignition of aerosol-generating article and it is only natural for a skilled
person to select the material which is capable of dissipating or spreading
heat and aluminium foils have been frequently used for high thermal
conductivity.
26.
D6 relates to a heated or combustible smoking article with a tipping
paper formed of a sheet material. It discloses use of sheet material as an
outer wrapper for a heated smoking article since the wrappers are
sufficiently heat resistant. D7 read with teachings of D1 makes the invention
obvious. D7 clearly teaches that the wrapper can be a metal foil with high
thermal conductivity such as aluminium foil and the desire to avoid
combustion of tobacco sheet and para [0034] thereof describes a wounded
sheet of tobacco, which is equivalent to a gathered sheet. Likewise,
teachings of D1 with prior arts D8-D10 show that thermally conductive
material is or comprises metal foil, preferably formed by co-lamination of
metal foil with paper or a sheet material formed by co-lamination of metal
foil with reconstituted tobacco and thus, the claims in the claimed invention
do not recite any inventive feature. No technical advancement in the art has
been shown by the patentee and all that is claimed is an article, which is
already in the public domain.
27.
Claim 1 is directed to aerosol-generating article and not aerosol-
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
generating device and does not recite any constructional feature. Positioning
of the thermal conductive wrapping material at the distal end of the article is
defined in Claim 4. In any case, comparison of aerosol-generating article
alone in IN’250 with cigarette coupled to a device, is erroneous. Claim 1 of
corresponding US application was held to be obvious in view of D1 in nonfinal rejection, which was later abandoned by the patentee. Most
importantly, Controller failed to identify the person skilled in the art,
contrary to the decision in F.Hoffmann-La Roche Ltd. & Anr. v. Cipla
Ltd., 2015 SCC OnLine Del 13619 and sans this exercise, there could be no
determination of whether the use of thermally conductive wrappers for heat
spreading and ignition mitigation would have been obvious in light of cited
prior art and consequently, of motivation and obviousness. Independent
Claim 1 is extremely broad and does not define any constructional feature
and features allegedly different from D1 are defined in dependent claims and
not in independent Claim 1 viz., positioning of thermally conductive rapid
material at the distal end is defined in dependent Claim 4; plurality of
elements and outer cigarette paper is defined in dependent Claims 2 and 3;
and insertable heating element is defined in dependent Claim 10.
28.
Controller has erred in excluding additional documents D7-D10 filed
by the Appellant under Rule 62(4) of 2003 Rules on 31.05.2024, which
clearly demonstrated lack of inventive step in the granted patent. D7 relates
to heated aerosol-generating article for use with an electrically operated
aerosol-generating device (Figure 2 of D7 and para [0029]) and teaches that
the wrapper can be a metal foil with high thermal conductivity such as
aluminium foil and the desire to avoid combustion of the tobacco sheet. D7
also teaches that aluminium foil has high heat conductivity, which reduces
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
propensity of ignition of smoking articles by using materials such as metal
foil of aluminium and its fire proof and flame retardant properties. Nonconsideration of D7 owing to erroneous interpretation of paragraph 40 of the
judgment in Pharmacyclics LLC v. Union of India and Ors., W.P.(C)
12105/2019, decided on 20.11.2019, has prejudiced the Appellant. 2003
Rules do not carve out any distinction between first scheduled date of
hearing and adjourned date of hearing and Rule 62(4) only uses the term
‘hearing’. Moreover, this Rule has to be read with Rule 129A, which
provides for adjournment and uses the term ‘hearing’. It is overlooked that
the observation in paragraph 40 applies to Rule 60, which concerns ‘further
evidence’ and not to publications under Rule 62(4) and paragraph 41
supports this position. D7 was the prior art relied upon by Board of Appeal
for revoking the EP counterpart of IN’250 for lack of novelty.
Submissions on behalf of the Controller
29.
Controller rightly excluded consideration of additional documents
D7-D10, which were filed beyond the permissible time limit. Time for any
publication under Rule 62(4) is five days prior to hearing as notified under
Rule 62(1), which means the first scheduled hearing date and not the
adjourned date of hearing. Section 25(2) provides one year for filing postgrant opposition and therefore, an opponent has an opportunity to file
revocation under Section 64(1). Under Rule 57, opponent files evidence and
has further opportunity under Rule 59, which mandates that reply statement
and evidence should be strictly confined to evidence under Rule 58.
Additionally, opponent can file further evidence under Rule 60. The first
hearing in the matter was scheduled for 30.04.2024 and thus relying on the
judgment in Pharmacyclics (Supra), Controller rightly held that five-day
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
notice period for filing new publications under Section 62(4) has to be
calculated with respect to first scheduled date of hearing and excluded the
time barred additional documents. Allowing evidence to be filed piecemeal
before every adjourned hearing would defeat the objective of expeditious
disposal and allow parties to indefinitely prolong proceedings.
30.
Even on merits, Appellant has no case. Controller has passed a
detailed and speaking order holding that the granted patent neither lacks
novelty nor inventive step and none of the other objections were made out.
Appellant’s challenge to novelty is primarily based on D1 and Controller has
rightly found that D1 does not anticipate the claimed invention as both are
structurally and functionally different. Structurally, patent claims require an
aerosol forming substrate comprising a gathered sheet of aerosol forming
material. D1 discloses tobacco rod or gathered web which is not the specific
gathered sheet configuration in the patent i.e. a sheet folded and convoluted
to occupy tri-dimensional space and does not anticipate the specific
structural limitations of the gathered sheet in Claim 1.
31.
Functionally, there is a critical technical difference in the purpose of
the wrapper, which in D1 is designed to be in contact with an internal
heating element and is meant to transfer heat inward to the tobacco substrate
to facilitate aerosol generation, in stark contrast to the wrapper in the granted
patented which functions as a thermally conducting flame barrier designed
to dissipate heat in the event flame is applied with lighter etc. and thus
protects the substrate from ignition or combustion. Controller correctly held
that the flame barrier quality is a functional limitation derived from article’s
special construction since invention lies not in the material itself, but in the
inventive manner in which the material is positioned and employed to solve
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
a specific technical problem of preventing external ignition, which is distinct
from its inherent physical properties. Controller noted positional difference
in the wrapping material of D1 on a visual comparison of Figure 2 of the
patent and Figure 3 of D1, which revealed that the wrapping material in D1
is located deep inside the device or near the mouthpiece and observed that
no user will apply flame around the wrapping material of D1 given its
internal or proximal location and hence, D1 fails to disclose a wrapper
positioned and configured to act as a flame barrier against external ignition
sources, which confirms the novelty of claimed invention.
32.
Appellant’s contention on lack of inventive step owing to D1 with
D2-D6, also lacks merit as the prior arts are in distinct fields of invention
and teach away from the granted claims. D2-D6 relate exclusively to
combustible smoking articles, where the objective is to burn the tobacco or
fuel element, whereas D1 and granted Claim 1 relate to electrically heated,
non-combustible aerosol generating articles and a person skilled in the art in
electrically heated devices would not look to the field of combustible
cigarettes for solutions to the technical problems solved in Claim 1.
Furthermore, D2-D6 teach the use of metal foils to retain heat or transfer
heat from a fuel source to the tobacco to promote combustion. The objective
of granted claims is to use the foil to shield the tobacco from external flame
and prevent combustion. Combining a teaching that promotes heat transfer
for combustion with a device designed to avoid combustion would be
counter intuitive. The prior arts clearly teach away from the invention and
there is no motivation for a person skilled in the art to combine these
disparate references to arrive at the claimed invention.
33.
Appellant’s objection under section 3(d) is equally misplaced. Firstly,
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
as recorded in the impugned order, there was no discussion on the subject
before the Controller during the hearing and thus it is not open to plead this
ground. Secondly, the subject matter of the granted patent is a heated aerosol
generating article with a specific mechanical construction comprising
gathered sheet substrate radially encircled by a thermally conductive
flame barrier. This constitutes a new product or article of manufacture and is
not merely the use of a substance. Controller examined the complete
specification and correctly determined that the disclosure was sufficient. The
claims specification, particularly, through Figures 2-4 and the accompanying
description, clearly delineates the construction of the article, positioning of
the wrapper and its function as a flame barrier. The disclosure provides
adequate technical details to enable a person skilled in the art to perform the
invention, thereby satisfying the requirements of the provisions of 1970 Act
and for all these reasons, the appeal deserves to be dismissed.
Submissions on behalf of the Patentee
34.
Controller rightly excluded documents D7 to D10 filed by the
Appellant under Rule 62(4) of 2003 Rules as time barred documents.
Appellant failed to file evidence or submissions under Rule 59 within the
prescribed time limit, in response to reply statement under Rule 58 by the
Patentee on 17.02.2023 and to overcome this lacuna, additional documents
were filed under Rule 62(4), which were rightly not accepted inasmuch as
the five day notice period is with respect to first scheduled hearing date,
which was 30.04.2024 and not the adjourned hearing date and this issue has
been settled by this Court in Pharmacyclics (Supra), on which the
Controller has relied.
35.
On merits, the objections in the post-grant opposition are untenable in
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
law. The invention claimed under the patent relates to an aerosol-generating
article having an aerosol-forming substrate adapted to release volatile
compounds to form an aerosol through heating rather than combustion of the
substrate. Such an article in the claims, with corresponding support in PCT
publication contrasts with conventional cigarettes which are ignited and
combusted and rely on the ignition by flame from a match or lighter. The
heated aerosol-generating article does not include a combustible heat source
and is adapted for use with an electrically operated aerosol-generating
device with an insertable heating element and also contrasts with articles
incorporating a combustible heat source to generate heat necessary for
volatile compounds to be released from the aerosol-forming substrate as also
an article heated from outside through a wrapper.
36.
Claims in the granted patent include an aerosol-forming substrate
comprising a gathered sheet of aerosol-forming material, which is one that is
convoluted, folded or otherwise compressed or constricted transversely, as
supported in the PCT application. The aerosol-forming substrate is radically
encircled by a sheet of thermally-conductive material and is not heated
through this sheet. The wrapper acts as a thermally-conducting flame barrier
for spreading heat and mitigating the risk of a user igniting the aerosolforming substrate in the event user applies flame to the aerosol-generating
article and the technical problem that the invention solves is to avoid
combustion of the substrate, which in turn reduces generation of various
smoke constituents associated with combustion and pyrolytic degradation of
tobacco in conventional cigarettes. It also overcomes the poor user
experience from using aerosol-forming articles when they are ignited rather
than heated.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
37.
Appellant had restricted his arguments in the post-grant opposition to
only two grounds i.e. lack of novelty and lack of inventive step and both
objections are misconceived. It is trite that a claim is judged novel unless a
single prior art reference discloses every element of the challenged claim
and enables a person skilled in the art to reach the invention, which means
that anticipation requires presence of a single prior art disclosure of each and
every element of the claimed invention and even a minor or insubstantial
difference between the claimed invention and prior art will mean that there
is no anticipation. The Manual of Patent Office Practice & Procedure (Patent
Manual) in para 09.03.02 under the Head ‘Novelty’, describes that “A prior
art is considered as anticipating novelty if all the features of the invention
under examination are present in the cited prior art document. The prior art
should disclose the invention either in an explicit or implicit manner.
Mosaicing of prior art documents is not allowed in the determination of
novelty.” This is the well recognized ‘all elements’ rule.
38.
In the instant case, none of the cited prior arts singly disclose all
elements of the patented claims. Appellant relied on D1 for proving lack of
novelty qua Claim 1. Board of Opposition found that D1 only discloses the
metallic foil as serving to transfer heat from the heating elements to the
tobacco enclosed by the wrapping material and does not explicitly teach that
the taught metal foil wrapper is a thermally conducting flame barrier
configured to spread heat and to mitigate against risk of ignition of the
aerosol-forming substrate by application of flame to the heated aerosolgenerating article and has rightly given weightage to the functional
limitation of Claim 1. This also negates the argument of the Appellant that
claim has been granted for functionality standalone. In any case, functional
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
limitation is recognized by Patent Manual under Head 09.03.05.05 stating
that “for the existence of a combination invention requires that the
relationship between the features or groups of features be one of functional
reciprocity or that they show a combinative effect beyond the sum of their
individual effects. The features should be functionally linked together which
is the actual characteristic of a combination invention”. Patentee has limited
its claim to the function of thermally-conductive wrapper in such a way that
the overall aerosol-generating article cannot be ignited when flame is
applied.
39.
The problem statement of D1 is that smoking articles that employ
tobacco substitute materials or sources of heat other than burning tobacco
cut filler to produce tobacco-flavored vapors or visible aerosols have not
received widespread commercial success and thus it tries to provide a
smoker with an article, which has the ability to use tobacco without
necessity of burning significant amount of tobacco. So, the problem of D1
was never of igniting the smoking article by someone inadvertently or
accidentally applying flame. Further, the tobacco material in D1 is in the
form of a tobacco rod circumscribed by a wrapping material and positioned
between the second resistance heating element and the mouth-end of the
outer housing. The aerosol-generating device and the whole arrangement of
D1 is complex as it uses three heating elements to heat the tobacco rod
whereas the heating element used in claimed invention is only one.
Moreover, the arrangement of the heating element in D1 is tubular which
circumscribes the whole rod unlike the claimed invention. Even the substrate
material in D1, which is a gathered sheet or web, is different and cannot be
equated with the aerosol forming substrate in the claimed invention.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
Illustratively, D1 describes that the cartridge can contain an upstream
segment composed of tobacco filler or processed tobacco filler material
incorporating aerosol-forming material and a downstream segment
composed of a substrate such as fibres of polyethene terephthalate carrying
flavors and/or aerosol forming material. It is clear that the substrate can be
gathered sheet and not the whole tobacco plus the substrate.
40.
Paras [0098] and [0099] in D1 describe that the wrapping material is
wrapped around the tobacco in such a way that each end of tobacco rod is
open and exposes the tobacco therein and allows passage of drawn air.
According to the teaching of D1, the wrapping material can be a paper or a
metallic foil and the wrapper acts as a heat sink (medium), which passes the
heat inside the tobacco rod from the heating element of the aerosolgenerating device of D1 to generate aerosol. The wrapper around the
tobacco is meant to be in contact with the heating element whereas that in
the claimed invention it acts as a flame barrier and is not in contact with the
heating element. The wrapper used in Claim 1 is a heat dissipating device,
which acts as a thermally-conducting flame barrier for spreading heat and
mitigating against the risk of a user igniting the aerosol-forming substrate by
applying flame to aerosol-generating article. Thus, applying the all-element
rule, D1 fails to disclose all features of Claim 1 and the wrapper in D1 will
not enable a person skilled in the art to make the aerosol-generating article
as in Claim 1 of the claimed invention, where the wrapper has a different
purpose than actual heating by a heating element and thus does not kill the
novelty. Moreover, Appellant has not challenged the dependant Claims 210, which ought to have been done to invalidate the patent, since Patentee
has protection in 10 different embodiments.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
41.
Controller has rightly rejected the objection of the Appellant on
ground of lack of inventive step. For determination of inventive step/nonobviousness, technology in two or more prior arts must originate within an
analogous art and once the analogous art is identified, it should be combined
by a person skilled in the art before the priority date of the claimed invention
in question. A claimed invention is obvious when there is a teaching,
suggestion or motivation to combine prior art teachings. In the instant case,
prior arts D2 to D6 are not analogous art to the subject matter disclosed in
D1, which relates to electronic cigarettes wherein tobacco is heated and not
burned or combusted, whereas D2 to D6 are related to conventional
cigarettes, which burn the tobacco in a conventional way. Thus,
identification of D2-D6 for combining with D1 is impermissible in law. D1
contains no indication of being concerned with mitigation of risk of ignition
of the tobacco in the event flame is applied to the cigarette and there is no
teaching of how wrapping material might be adapted to perform this
function.
42.
Prior art D2 relates to tobacco products such as smoking articles, such
as cigarettes. D2 discloses numerous embodiments of smoking articles,
which fall into two groups: (a) first group, in which a lighting end segment
22, heat generation segment 35 and aerosol-generating segment 51 are
successively axially aligned relative to each other; and (b) second group, in
which the lighting end segment 22 is omitted. However, all smoking articles
rely on ignition and combustion of part of the smoking article in a manner
similar to conventional cigarettes and none are heated aerosol-generating
articles within the meaning of Claim 1. For ready reference, Figure 1 is as
follows:
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
43.
The Figure demonstrates that lighting end segment 22 includes
smokable material 26. The heat generation segment 35 has a heat source 40
circumscribed by insulation 42. Aerosol-generating segment 51 includes a
substrate material 55 acting as a carrier for an aerosol-forming agent or
material. Para [0024] of D2 discloses the wrapping material having heat
conductive properties and being in the form of metal or metal foil, where the
metal foil can conduct heat from the heat generation segment 35 to the
aerosol-generating segment 51 to volatilise aerosol-forming components
contained therein. Para [0026] discloses that the wrapping material 58 can
be adapted to facilitate transfer of heat from the heat generation segment 35
to aerosol generating segment 51. Para [0036] discloses that to use the
smoking article is lit at the lighting end 14 using a match or cigarette lighter
in the same manner as in the conventional cigarettes. The smoking article
relies only on ignition and burning of the substrate and is thus not a heated
aerosol-generating article. The wrapping material in D2 performs a function
different from the wrapper in Claim 1, where the sheet acts as thermallyconducting flame barrier. Second group of D2 lacks the lighting end
segment 22 of the smoking articles as below:-
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
44.
For the smoking articles, as visible from the above Figure, the heat
generation segment 35 forms the lighting end 14. The smoking articles 10
disclosed in D2 rely on ignition and combustion of part of the smoking
articles. For the smoking articles in Figure 1 lighting end segment 22 is lit
while for smoking articles of Figure 7, heat generation segment 35 is lit. As
the smoking article of D2 rely on combustion to generate heat, they are
clearly not adapted for use with an electrically operated aerosol-generating
device comprising a heating element and for this reason, skilled person
would not use D2 as a starting point to arrive at the invention even in
combination with D1 and hence, Claim 1 is inventive over D2, when seen
alone.
45.
Prior art D3 relates to smoking articles (cigarettes), particularly, those
employing tobacco and the summary under D3 discloses that the invention is
directed towards improvement in fuel element compositions by reducing
release of carbon monoxide during combustion of fuel elements and thus the
smoking articles in D3 do not relate to the field of “heated aerosolgenerated articles” within the meaning of Claim 1, specifically those
adapted to release volatile compounds to form an aerosol through heating
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
rather than combustion of an aerosol-forming substrate. Further, as the
cigarettes of D3 rely on combustion, they are not adapted for use with an
electrically operated aerosol-generating device comprising a heating element
and therefore, skilled person will not consider D3 to address the problem of
the claimed invention.
46.
There is no teaching in D3 of the barrier tube or wrapper having
capability to reduce the risk of ignition of the substrate in the event flame is
applied to the cigarette. Rather, D3 discloses use of metal foil for the barrier
tube wrapper to reduce or eliminate any migration of the aerosol former
from the substrate to the other components of the cigarettes and lacks any
teaching of a wrapper being a thermally conducting flame barrier for
spreading heat and mitigating against the risk of a user igniting the aerosol
forming substance by applying flame to the aerosol-generating article. Even
the presence of metal as part of barrier tube wrapper does not prevent
ignition of the material enclosed therein.
47.
Prior art D4 relates to smoking articles in which ignition and
combustion of part of the smoking articles is intended and therefore, none of
the smoking articles of D4 are “heated aerosol-generated articles”. Figure 2
shows a smoking article 10 having a tobacco rod 12 circumscribed by a
metallic foil 14. D4 is silent about the form of the tobacco in the tobacco
rod. Cylinder 16 of non-tobacco fuel surrounds the foil 14 with the cylinder
circumscribed by an air-permeable wrapper 18. Lines 20 to 23 disclose the
metallic foil 14 as preferably being a laminate of layer of paper 14A and a
layer of aluminium 14B. In use, the non-tobacco fuel cylinder combusts or
burns with heat from the fuel cylinder getting transferred through foil 14 to
heat the tobacco rod 12. D4 therefore, relies on combustion and ignition of
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
part of smoking article and does not relate to heated aerosol-generated
articles and thus the smoking article is not adapted for use with an
electrically-operated aerosol-generating device comprising a heating
element. The wrapper in D4 is formed of or includes metal and at least part
of the article is ignited or burnt and the metal wrapper is not configured to
act as a thermally-conducting flame barrier. A person skilled in the art will
not be motivated to reach the invention from the teachings of D4. The
relevant Figure is as follows:
48.
D5 prior art relates to smoking articles intended to produce an aerosol
resembling tobacco smoke but contains minimal amount of incomplete
combustion or pyrolysis products albeit it relates to smoking articles in
which ignition and combustion of part of the smoking articles is intended
but none of them are “heated aerosol-generated articles”, within the
meaning of Claim 1 of the patent. The smoking article of Figure 1 below has
a combustible carbonaceous fuel element 10 followed by an aerosolgenerating means 12 and fuel element is made of charcoal and is intended to
be lit/ignited. The aerosol-generating means is in the form of glass beads 20
coated with aerosol-forming substance such as glycerine. An aerosol
delivery passage 26 extends between aerosol-generating means 12 and a
mouth end 15 of the article and a foil lined paper tube 14 circumscribes part
of fuel element 10 and all of the aerosol-generating means 12, porous
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
disc 22 and aerosol delivery passage 26. The tube 14 increases heat transfer
to the aerosol generator and the foil helps to extinguish the fire cone due to
heat loss through the foil. Therefore, D5 also does not relate to the field of
“heated aerosol-generated articles”. The presence of foil in the tube does
not prevent ignition of material enclosed by the tube and therefore, D5
relates to smoking articles in which ignition and combustion is intended and
they are not adapted for use with electrically operated aerosol-generating
device and lack any teaching of a wrapper having the property of acting as
thermally-conductive flame barrier. The relevant figure is as follows:-
49.
Prior art D6 relates to smoking articles having heat resistance sheet
material in which ignition and combustion of part of the smoking article is
intended and none of the smoking article are “heated aerosol-generated
articles”. Figure 2 below shows a smoking article having a combustible heat
source 22, an aerosol-generating substrate 24, an expansion chamber 26 and
a mouth piece 28 coaxially aligned with each other. An outer wrapper 30
circumscribes part of the combustible heat source 22 and all of the aerosolgenerating substrate 24, expansion chamber 26 and mouth piece 28. The
combustible heat source is disclosed as being a pyrolysed porous carbonbased heat source. The aerosol-generating substrate is disclosed in the form
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
of “longitudinally aligned filaments of extruded tobacco material.” The
outer wrapper is formed of a fibrous based layer 12 coated with an inner
coating layer 14 and an outer coating layer 16, which is disclosed as being
heat resistance but none of the materials show that outer wrapper 30 is
thermally conductive. A heat conducting element 40 in the form of a tube of
aluminium foil surrounds and is in contact with a rare portion 22b of the
combustible heat source 22 and a front portion 24a of the aerosol-generating
substrate. D6 does not relate to “heated aerosol-generated articles” within
the meaning of Claim 1 of the patent and the smoking articles are not
adapted for use with electrically operated aerosol-generating device
comprising a heated element and there is no teaching in D6 that the heat
conducting element 40 of aluminium foil has the capability of reducing risk
of ignition in the event of a flame being applied. D6 at best relates to
combustible articles having a wrapper formed of or including metal, with at
least part of the article being ignited and burnt during use and the wrapper is
not configurated to act as a thermally conducting flame barrier. Figure 2 of
D6 is as follows:-
50.
Claims of the subject patent, therefore, involve inventive steps over
the disclosure of cited documents D1 to D6 and even the Board of
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
Opposition opined that Claims 1 to 10 involve inventive steps and Section
25(2)(e) is not applicable. In Novartis AG v. Union of India and Others,
(2013) 6 SCC 1, the Supreme Court observed that ‘obviousness’ is judged
based on hypothetical construct of a person of ordinary skill in the art, who
must belong to the relevant field; looks at the prior art; and is well aware of
the fact that even a small structural change in a product or procedure can
produce dramatic functional changes. In the instant case, a person skilled in
the art will not be motivated to look for D1 to D6 as starting points to reach
the patented invention. Thus, the post-grant opposition was rightly rejected
and the Appeal be dismissed, being devoid of merit.
51.
Heard learned Senior Counsel for the Appellant/Writ Petitioner and
counsels for Respondents and examined their rival submissions.
WRIT PETITION:
52.
The writ petition is opposed by the Respondents, both on
maintainability and merits. On maintainability, the argument is that
impugned order dated 30.01.2025 dismissing the two IPs having been
passed under Section 25(4) of 1970 Act is an appealable order under Section
117A(2) of 1970 Act assuming the IPs could be filed and hence, writ
jurisdiction cannot be invoked. Appellant contends that if there is violation
of principles of natural justice, writ petition is the appropriate remedy and,
in any case, existence of alternate remedy is not always a bar in entertaining
the petition.
53.
Similar issue arose before this Court in Best Agrolife (Supra), where
Respondents had raised an objection to the maintainability to the writ
petition filed by the Petitioner challenging the order of the Controller
dismissing pre-grant opposition and allowing the grant of patent, on the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
ground that an alternative efficacious remedy was available to the Petitioner
in terms of post-grant opposition under Section 25(2) of 1970 Act as also
revocation petition under Section 64. Referring to and relying on several
judicial precedents, Court rejected the preliminary objection observing that
there cannot be a debate that the 1970 Act provides remedy of post-grant
opposition and/or revocation to a “person interested”, who is unsuccessful in
a pre-grant opposition, however, if Petitioner is able to substantiate violation
of principles of natural justice and/or failure in exercising jurisdiction and/or
non-consideration of vital grounds/documents, Petitioner cannot be nonsuited in a writ petition. Appellant herein has alleged that there was violation
of principles of natural justice by the Controller while considering the IPs.
Hence, in light of the judgement in Whirlpool Corporation (Supra), where
the Supreme Court perspicuously explained the scope and ambit of judicial
interference in a writ jurisdiction where an alternative remedy is available to
a party as also Best Agrolife (Supra), writ petition is held to be
maintainable.
54.
Broadly speaking, three-fold issues arise for consideration in the writ
petition. First is whether the Controller was right in deciding IP-I dated
14.08.2024, filed by the Appellant opposing the request of the patentee to
take on record two auxiliary claim sets and IP-II dated 21.09.2024 for
rejecting the second written submissions filed by the patentee on
04.09.2024, allegedly being beyond the earlier written submissions dated
21.06.2024, pleadings in reply statement and oral submissions made during
the hearing on 20.08.2024, by a common order and treating both as
oppositions to the auxiliary claim amendments. Perusal of the impugned
order dated 30.01.2025, whereby the two IPs were dismissed under Rule
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
58(2) of the Patent Rules, 2016, substantiates the case of the Appellant that
Controller has decided IP-II under an erroneous impression that it concerned
the claim amendments, contrary to the reliefs prayed therein. Appellant is
thus entitled to be heard on the grievance raised in IP-II.
55.
Parties made extensive arguments on both the IPs before this Court.
Main plank of Appellant’s argument was that contents of second written
submissions are beyond the earlier pleadings/written submissions and no
opportunity was given to rebut, which has caused grave prejudice. Appellant
has filed a comparative table as Document-A to the written submissions
dated 23.01.2026, which is extracted in the earlier part of the judgment, to
demonstrate that fresh points were included in the second submissions,
which became the basis of rejection of post-grant opposition, such as the
composition, properties and role of the wrapper material.
56.
Having perused the order, written submissions and the claims
specifications, I am unable to agree with the Appellant on this issue.
Controller has observed that D1 in para [0099] describes that the wrapping
material can vary and can be a paper material of the type traditionally used
for cigarette manufacture and can also be composed of a laminate of
metallic foil and paper, whereas the thermally-conducting sheet in the
opposed patent is a metallic foil and it is clear that a laminate will have
different thermal conductivity than a metal foil, which is only composed of
metal and therefore, D1 fails to teach this functional limitation of Claim 1 of
the opposed patent. In the written submissions dated 04.09.2024, Patentee
stated that there is a mention of laminate of paper and metal foil in D1 and
there is a difference between a laminate comprising paper and metal foil and
a metal foil since metal foil is made of metal and retains the inherent
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
properties associated with the metal it is made of, whereas laminate foil
comprises many layers fused together, of which metal may be one of the
layers. Further, ignition temperature of a laminate foil is generally below the
flame temperature of a smoking lighter or matchstick, whereas ignition
temperature or at least melting point of metal foil is the same as that of the
metal of which the metal foil is made.
57.
Firstly, it is elementary knowledge in science that metal foil is a
homogeneous single-material system whereas metal-paper laminate is a
multilayer system and thus, metal foil will exhibit intrinsic properties of the
metal it is made of while the laminate’s properties will depend on properties
of the constituent layers. Thus, Appellant cannot urge that this observation
was influenced by Patentee’s second written submissions. Secondly and
more importantly, this distinction is embedded in the claim language
itself which expressly identifies metal foil and metal foil laminates with
paper or re-constituted tobacco as alternative for the thermally-conductive
material.
58.
Appellant next joins issue with Controller’s finding that D1 does not
disclose gathered sheet of tobacco unlike the one in the specification of the
opposed patent. On analysis of the prior art it emerges that Controller’s
finding that D1 fails to disclose that the aerosol-forming substrate comprises
a gathered sheet of aerosol-forming material is based on para [0089] of D1,
which makes a reference to a web of re-constituted tobacco sheet that is
gathered so as to possess a plurality of longitudinally extending passage
ways, which can be treated with mixture of propylene glycol, flavouring
agent and tobacco extract and is not purely based on the written submissions
of the Patentee. Controller has further compared the gathered sheet of the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
aerosol-forming material of granted patent as defined in lines 31-33 of
complete specifications, which states that the sheet of tobacco material is
convoluted, folded or otherwise compressed or constricted substantially
transversely to the cylindrical axis of the rod and then applied the common
general knowledge that gathered sheets of tobacco material are widely used
in the tobacco industry and the term has a clear and agreed meaning in the
art i.e. a sheet which is gathered when it is folded and convoluted to occupy
a tri-dimensional space. In the second written submissions, Patentee has
merely explained the scope and technical significance of the gathered sheet
in the claim specification as an argument and there is nothing which is
outside the claims or beyond pleadings and hence, there is no merit in the
objections raised in IP-II. I will advert to the technical aspect of the
difference in the wrapper material and gathered sheet in detail in the later
part of the judgement.
59.
There is also no legal infirmity in dismissal of IP-I, filed against the
proposed amendment to the existing claims by adding two auxiliary claim
sets. As a matter of record, on 25.07.2024 Controller issued second hearing
notice to the parties scheduling the hearing on 20.08.2024 to discuss the two
auxiliary claim sets and during the hearing, Patentee was advised by the
Controller to follow the procedure of amendment governed by Section 57 of
1970 Act, more particularly, in sub-Section (3) thereof. Patentee did not
follow the amendment procedure and decided to proceed with the existing
claims and filed written submissions on 04.09.2024 on that basis. Since
patentee did not press the amendment, there was no reason to hear the
opposition and IP-I was rightly dismissed. Thus, there is no merit in the writ
petition and the same deserves to be dismissed.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
APPEAL
60.
This appeal is filed by the Appellant challenging order dated
30.01.2025 dismissing its post-grant opposition against opposed patent
IN 384250 titled “HEATED AEROSOL GENERATING ARTICLE WITH
THERMAL SPREADING WRAP”, granted in favour of the patentee on
14.12.2021. The post-grant opposition was filed on 16.12.2022 and grounds
of opposition were lack of novelty under Section 25(2)(b), prior use/prior
knowledge under Section 25(2)(d), lack of inventive step/obviousness
Section 25(2)(e), not an invention under Section 25(2)(f) and insufficiency
of disclosure Section 25(2)(g) of 1970 Act. Appellant cited prior art
documents D1 to D6 to oppose the patent at the initial stage. Opposition
Board made recommendations in favor of the Patentee that the invention
claimed in the patent was novel and inventive and rejected the grounds of
the Appellant through its joint recommendation dated 12.10.2023. The first
hearing in the matter was scheduled for 30.04.2024, however, Appellant
sought adjournment and on 31.05.2024, filed additional documents D7 to
D10 under Rule 62(4) of 2003 Rules. Controller excluded these documents
from consideration as being time barred observing that five days’ notice
period envisaged in the said rule has to be computed with respect to the first
scheduled date of hearing and not the adjourned date, relying on the
judgment in Pharmacyclics LLC (Supra). It was held that the first
scheduled date of hearing being 30.04.2024, the deadline for filing any
additional document expired on 25.04.2024 and the additional document
filed thereafter on 31.05.2024, could not be accepted. Post-grant opposition
was rejected taking into consideration prior arts D1 to D6 only. It needs a
mention that Controller has in paragraph 5 of the impugned order noted that
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
during the hearing, counsel for the Appellant did not address arguments on
objections under Section 3(d), 3(f) and 3(g) of 1970 Act. For this reason,
this Court is also not delving into these objections and be it noted that the
arguments canvassed on behalf of the respective parties were largely
restricted to objections of novelty and lack of inventive steps.
61.
The granted patent relates to aerosol-generating articles in which an
aerosol-forming substrate is adapted to release volatile compounds to form
an aerosol through heating rather than combustion of the substrate. The
article is referred to as a “heated aerosol-generating article” in the claims,
with corresponding support found in lines 10-19 of the PCT publication and
does not include a combustible heat source as also contrasts heated aerosolgenerating articles in conventional cigarettes, which are ignited and
combusted. The heated aerosol-generating article is adapted for use with an
electrically operated aerosol-generating device having an insertable heating
element to heat the aerosol-forming substrate of the article. The technical
problem sought to be resolved and/or technical advancement claimed is:
(a) avoiding combustion of aerosol-forming substrate may reduce generation
of various smoke constituents associated with combustion and pyrolytic
degradation of tobacco in conventional cigarettes (lines 8 to 10 of PCT
publication); and (b) aerosol-forming substrates designed for use in heated
aerosol-forming articles typically provide a poor user experience if they are
ignited rather than heated (lines 27 to 29 of PCT publication).
62.
Therefore, the technical problem being addressed is how to mitigate
against the risk of a user igniting the aerosol-forming substrate in a heated
aerosol-generating article used in an electrically operated aerosol-generating
device and the invention lies in the wrapper (5060), circumscribing the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
aerosol forming substrate comprising a gathered sheet of aerosol forming
material, which is of thermally conductive material that acts as a thermallyconducting flame barrier for spreading heat and mitigating against the risk of
a user igniting the aerosol-forming substrate (1020, 2020) in the event the
user applies flame to the aerosol-generating article. The granted set of
claims have been extracted in the earlier part of the judgement. The heated
aerosol-generating article illustrates in Figure 2 an embodiment of a heated
aerosol-generating article (1000, 2000) comprising:
an aerosol-forming substrate (1020, 2020) radially encircled by
a sheet of thermally-conductive material (1222, 2222)
in which the aerosol-forming substrate (1020, 2020) comprises
a gathered sheet of aerosol-forming material
circumscribed by
a wrapper (5060), being the sheet of thermally-conductive
material
which acts as a thermally-conductive flame barrier for
spreading heat and mitigating against the risk of a user igniting the
aerosol-forming substrate (1020,2020) by applying a flame to the
aerosol-generating article (1000, 2000).
63.
Figure 2 illustrates that article 1000 comprises four elements: aerosol-
forming substrate 1020, a hollow cellulose acetate tube 1030, a spacer
element 1040 and a mouth piece filter 1050, which are arranged sequentially
and in coaxial alignment and are assembled by a cigarette paper 1060 to
form the aerosol-generating article. The article 1000 has a mouth end 1012,
which a user inserts into his/her mouth during use and a distil end 1013
located at the opposite end of the article to the mouth end. Aerosol forming
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
substrate comprises a rod formed from a crimped and ‘gathered sheet’ of
homogenised tobacco wrapped in aluminium foil 1222 to form a plug (lines
17-18 of specifications). In an industry gathered sheet means a sheet
convoluted, folded or otherwise compressed or constricted transversely.
Substrate is not heated through the sheet of thermally-conducting material
(wrapper) which circumscribes the gathered sheet and instead the wrapper
acts as a flame barrier for spreading heat and mitigating the risk of a user
igniting the aerosol-forming substrate in the event the user applies flame to
the article. Figure 2 is as follows:-
64.
Coming to the first objection of lack of novelty. It is settled that a
claim is not anticipated unless a single prior art discloses all elements of the
questioned claim, which means that all limitations of the claim should be
present in the single prior art document and even a minor difference between
the two will mean that there is no anticipation and the claim is novel. This
‘all element’ rule finds strength from para 09.03.02.6 under ‘Novelty’ in the
Patent Manual, which provides that a prior art is considered as anticipating
novelty if all features of the invention under examination are present in the
cited prior art document. The prior art should disclose the invention either in
an explicit or implicit manner and mosaicing of prior art documents is not
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
allowed in determination of novelty.
65.
Appellant challenges novelty in Claim 1 of the granted patent citing
D1 titled “Tobacco Containing Smoking Article”, stating that D1 anticipates
all elements of Claim 1 of impugned patent. Appellant highlighted that D1
discloses a smoking article incorporated with an electrically powered
aerosol-generating device, which also comprises of a heating element for
forming thermally-generated aerosol incorporating tobacco components. D1
relates to a cigarette that is smoked by coupling the cigarette to an
electrically powered aerosol-generating device that acts as a holder. In one
further embodiment, tobacco material is in the form of a rod circumscribed
by wrapping material and positioned between the second resistance heating
element and the mouth-end of the outer housing [para 0024]. The substrate
material can be used in the form of gathered web or sheet, using techniques
set forth in U.S. Pat. No. 4,807,809 to Pryor et al. [para 0064]. The wrapping
material is wrapped around the tobacco 89 so as to form a generally
cylindrical rod-shaped cigarette rod or tobacco rod. The tobacco is generally
positioned within the hollow region within the tube and the wrapping
material is formed such that each end of the tobacco rod is open to expose
the tobacco and to allow passage of drawn air [para 0098]. A representative
device possesses a source of electrical power e.g. a battery, a controller
mechanism including a sensor and at least one heating device for forming a
thermally-generated aerosol, which incorporates components of tobacco
Para [0013].
66.
Appellant referred to paras [0098] as also [0099] to emphasize that
the wrapping material in D1 can vary and can be a paper of the type
traditionally used for cigarette manufacture or can be composed of a
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
laminate of metallic foil and paper and as such, heat generated in the second
heating element can heat the metallic foil of the laminate and consequently,
the tobacco contained within it. Paras [0013], [0024], [0064], [0098], [0099]
and [0075] are extracted hereunder for ready reference:“Para [0013] In one embodiment, the present invention relates to a
cigarette that is smoked by coupling that cigarette to an electrically
powered aerosol generating device that acts as a holder for that cigarette.
The cigarette possesses at least one form of tobacco, and that tobacco is
wrapped in a paper wrapper. If desired, various forms of tobacco, or
various forms of tobacco containing compositions, can be positioned at
specific locations within the cigarette. The cigarette also incorporates
aerosol-forming material, and that aerosol-forming material can be an
ingredient that is employed in addition to the tobacco. The cigarette may
also possess a mouth-end piece that is used by the smoker to inhale
components of tobacco, components derived from tobacco, and other
components, preferably in the form of a visible aerosol, generated at least
in part by the action of heat upon components of that cigarette. A
representative device possesses a source of electrical power (e.g., a
battery), a controller mechanism including a sensor that is capable of
selectively powering certain components of the device (e.g., electrical
resistance heating elements) at least during periods of draw, and at least
one heating device (e.g., an electrical resistance heating unit) for forming
a thermally generated aerosol that incorporates components of tobacco.
During use, the cigarette is positioned within the outer housing of the
smoking article, and after use, the used cigarette is removed from the
smoking article. When desired, another cigarette is positioned within the
device for further use.
xxx
xxx
xxx
Para [0024] In one further embodiment, the tobacco material is in the
form of a tobacco rod circumscribed by a wrapping material and
positioned between the second resistance heating element and the mouthend of the outer housing. A cartridge comprising an aerosol-generating
material circumscribed by a wrapping material can be positioned between
the tobacco rod and the second resistance heating element. Preferably, a
filter element is attached to the end of the tobacco rod closest to the
mouth-end of the outer housing.
xxx
xxx
xxx
Para [0064] The substrate material can incorporate tobacco of some
form, normally is composed predominantly of tobacco, and can be
provided by virtually all tobacco material. The form of the substrate
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
material can vary; but most preferably that material is employed in an
essentially traditional cigarette, cigar or pipe filler form (e.g., as cut
filler). The substrate material can be otherwise formed into desired
configurations. The substrate material can be used in the form of a
gathered web or sheet, using the types of techniques generally set forth in
U.S. Pat. No. 4,807,809 to Pryor et al. The substrate material can be used
into the form of a web or sheet that is shredded into a plurality of
longitudinally extending strands, using the types of techniques generally
set forth in U.S. Pat. No. 5,025,814 to Raker. The substrate material can
have the form of a loosely rolled sheet, such that a spiral type of air
passageway extends longitudinally through the aerosol-generation
segment. Representative types of tobacco containing substrate materials
can be manufactured from mixtures of tobacco types; or from one
predominant type of tobacco (e.g., a cast sheet-type or paper-type
reconstituted tobacco composed primarily of burley tobacco, or a cast
sheet-type or paper-type reconstituted tobacco composed primarily of
Oriental tobacco).
xxx
xxx
xxx
Para [0075] Certain embodiments of the smoking article of the invention
incorporate a cigarette rod as a necessary component. That is, the
smoking article of the invention can incorporate a tobacco rod wrapped in
paper or other wrapping material. The wrapping material used as a
wrapper for containing the tobacco, and hence used for cigarette
manufacture, can vary. Exemplary types of wrapping materials are set
forth in U.S. Pat. No. 4,938,238 to Barnes et al. and U.S. Pat. No.
5,105,837 to Barnes et al. Wrapping materials, such as those set forth in
U.S. Patent Appl. Pub. No. 2005/0005947 to Hampl, Jr. et al. and PCT
Appl. Pub. No. WO 2005/039326 to Rasouli et al., can be employed as
inner wrapping materials of a so-called “double wrap” configuration. An
exemplary type of heat conductive wrapping material is set forth in U.S.
Pat. No. 5,551,451 to Riggs et al.; and other suitable wrapping materials
are set forth in U.S. Pat. No. 5,065,776 to Lawson et al. and U.S. Pat. No.
6,367,481 to Nichols et al.; each of which is incorporated herein by
reference. Exemplary wrapping materials, such as laminates of paper and
metal foil, and papers used as the outer circumscribing wrapper of the
heat generation segment, have been incorporated within the types of
cigarettes commercially marketed under the trade names “Premier” and
“Eclipse” by R. J. Reynolds Tobacco Company. Other representative
wrapping materials, and processed wrapping materials, suitable for use
for cigarette manufacture are set forth in U.S. Pat. No. 5,220,930 to
Gentry; U.S. Pat. No. 6,976,493 to Chapman et al.; and U.S. Pat. No.
7,047,982 to Seymour et al; and U.S. patent application Ser. No.
11/377,630 filed Mar. 16, 2006 to Crooks et al.; each of which is
incorporated herein by reference. Paper materials can be composed of
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
materials, or treated with films, in order to provide resilience, particularly
when the paper material is used to contain tobacco materials that are
substrates for relatively high amounts of liquid materials (e.g.,
aerosol-forming materials). For example, such papers can be treated with
coatings of nitrocellulose or ethylcellulose. Alternatively, paper materials
can be highly absorbent in nature, and can act as substrates for liquid
materials (e.g., aerosol-forming materials, liquid flavoring agents, or
mixture of aerosol -forming materials and tobacco extrac ts).
xxx
xxx
xxx
Para [0098] Typically, the wrapping material 160 is wrapped around
the tobacco 89 so as to form a generally cylindrical rod-shaped cigarette
rod or tobacco rod. That is, the wrapping material 160 is formed into a
generally tubular shape, and the tobacco is positioned within the hollow
region within that tube. Preferably, the wrapping material 160 is formed
such that each end of the tobacco rod is open to expose the tobacco
contained therein, and to allow the passage of drawn air therethrough.
Para [0099] The wrapping material 160 can vary. The wrapping
material 160 can be a paper wrapping material of the type traditionally
used for cigarette manufacture. The wrapping material 160 also can be
composed of a laminate of metallic foil and paper, and as such, heat
generated by the second heating element can heat the metallic foil of the
laminate and hence heat the tobacco contained within that laminate. See,
for example, the types of wrapping materials, wrapping material laminates
and wrapping material configurations set forth U.S. patent application
Ser. No. 11/377,630 filed Mar. 16, 2006 to Crooks et al.”
67.
As noted above, the Opposition Board recommended in favour of the
Patentee observing that subject matter of independent Claim 1 of the
opposed patent was new over disclosure of D1, which teaches a heated
aerosol-generating article configured to generate aerosol when heated for an
electrically operated aerosol-generating device comprising a heating
element. The heated aerosol-generating article comprises an aerosol-forming
substrate (89) radially encircled by a sheet (160) of thermally-conductive
material, the aerosol-forming substrate comprising a gathered sheet of
aerosol-forming material circumscribed by a wrapper, being a sheet of
thermally-conductive material comprising an aerosol-forming substrate,
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
comprising a gathered tobacco sheet circumscribed by a wrapper, wherein
the wrapper comprises a metallic foil configured to conduct heat. D1 further
teaches to assemble the substrate and at least one other element within the
wrapper, where the wrapper is a laminate of metallic foil and paper and only
discloses the metallic foil as serving to transfer heat from the heating
element to the tobacco. D1 does not explicitly teach that the taught metal
foil wrapper is a thermally-conducting flame barrier configured to spread
heat and mitigate against risk of ignition when flame is applied to the heated
aerosol-generating article. Taking into account, the respective contentions of
the Appellant and the patentee as also Board’s recommendations, Controller
rejected the ground of novelty citing prior art D1 and hence, the ground
under Section 25(2)(b). Relevant part of the order is as follows:“After carefully studying the disclosure of D1, I found that that D1 fails to
disclose the following features of claim 1.
1). aerosol-forming substrate comprises a gathered sheet of aerosolforming material; and
2). thermally-conductive material which acts as a thermally-conducting
flame barrier for spreading heat and mitigating against the risk of a user
igniting the aerosol-forming substrate by applying a flame to the
aerosol-generating article.
D1, fails to disclose that the aerosol forming substrate comprises a
gathered sheet of aerosol forming material. In fact, D1 clearly states that
two separate ingredients i.e., an aerosol-forming material positioned
within the outer housing which is in fluid communication with said
tobacco material. [Para-[0019] and [0020]. D1, does not disclose that the
aerosol material is a gathered sheet. The reference of gathered sheet in D1
is in para [0089] with regard to a web of reconstituted tobacco sheet that
is gathered so as to possess a plurality of longitudinally extending
passageways. The gathered sheet of aerosol forming material of the
opposed patent is defined on page 4 lines 31-33 of Complete specification
which states that the sheet of tobacco material is convoluted, folded, or
otherwise compressed or constricted substantially transversely to the
cylindrical axis of the rod. Gathered sheets of tobacco material are widely
used in the tobacco industry and as such the term "gathered sheet' has a
clear and agreed meaning in the art, this being that a sheet is gathered
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
when it is folded and convoluted to occupy a tri-dimensional space. In
particular, D1 does not talk about gathered sheet of tobacco in the sense
defined by the specification of the opposed patent let alone disclosing the
aerosol-forming material is gathered.
D1 also fails to disclose explicitly a thermally conducting material which
acts as a thermally-conducting flame barrier for spreading heat and
mitigating against the risk of a user igniting the aerosol-forming
substrate by applying a flame to the aerosol-generating article.
With regard to the above feature, the opponent has simply submitted that
this feature is a functional aspect of the sheet and would be inherent to
such metal foil wrappers. This argument cannot be followed. The making
of a heated aerosol generating article using a thermally conducting sheet
in a such a way that it will spread the heat if unknowingly a user apply a
flame to the aerosol generating article. The claim 1 of the opposed patent
is limited by this feature, therefore this feature cannot be ruled out from
the scope of the claim 1. As no mapping of this feature with respect to D1
has been provided by the Opponent in the opposition documents or
hearing, this feature is not disclosed by D1 and therefore D1 does not
anticipate claim 1.
Diagram to Diagram Comparison
Fig. 2 of the Opposed Patent
Fig. 3 of the cited documents
D1
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
Figure 2 illustrates an embodiment of a heated aerosol-generating article
1000 comprising a rod as described herein. The article 1000 comprises
four elements; an aerosol-forming substrate 1020, a hollow cellulose
acetate tube 1030, a spacer element 1040, and a mouthpiece filter 1050.
These four elements are arranged sequentially and in coaxial alignment
and are assembled by a cigarette paper 1060 to form the aerosolgenerating article 1000. The article 1000 has a mouth-end 1012, which a
user inserts into his or her mouth during use, and a distal end 1013
located at the opposite end of the article to the mouth end 1012. The
embodiment of an aerosol-generating article illustrated in Figure 2 is
particularly suitable for use with an electrically-operated aerosolgenerating device comprising a heater for heating the aerosol-forming
substrate.
Mouth Piece-15
Distal end-13
Wrapping material-160
Tobacco-89
From the above diagram to diagram comparison of the opposed patent
with D1 it is clear that this wrapping 160 material is wrapped around
tobacco 89 very, which is very close to the mouth piece 15 whereas in the
opposed patent thermally conducting-sheet 1222 (bold black in the above
fig. 2) is wrapped around aerosol-forming substrate 1020 at distal end
1013. Therefore, no user will apply a flame around the wrapping material
160 of D1 which is near to mouth piece 15. Therefore, construction and
working of aerosol generating article of the opposed patent and D1 is
starkly different.
Also, the wrapping material 160 in D1 is designed to be in contact with a
heating element. Para [0101] of D1 describes that the wrapping material
160 can be in electrical contact with the electrical circuitry associated
with the electrical resistance heating element 72, which will provide the
heat to the tobacco-89. Also, in some embodiment of D1 wrapper 160 is in
direct contact with third heating element-300.
D1 in para [0099] describes that the wrapping material 160 can vary. The
wrapping material 160 can be a paper wrapping material of the type
traditionally used for cigarette manufacture. The wrapping material 160
also can be composed of a laminate of metallic foil and paper. Whereas
the thermally conducting sheet in the opposed patent is a metallic foil.
Therefore, it is clear that a laminate will have different thermal
conductivity than a metal foil which is only composed of metal in contrast
to the laminate which is made of different sheet of metal and paper.
Therefore, D1 fails to teach this functional limitation of the claim 1 of the
opposed patent.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
In view of my above reasoning, I find claim 1 of the subject patent is novel
over prior art D1. Therefore, the ground under Section 25(2)(b) is
rejected.”
68.
The cited prior art D1 allegedly destroying novelty relates to smoking
articles that employ tobacco materials and the problem that it resolves is
captured in para [0010] as follows:“Para [0010] Smoking articles that employ tobacco substitute materials
and smoking articles that employ sources of heat other than burning
tobacco cut filler to produce tobacco-flavored vapors or tobacco-flavored
visible aerosols have not received widespread commercial success. Thus,
it would be highly desirable to provide a smoking article that provides a
smoker with an ability to enjoy using tobacco without the necessity of
burning any significant amount of tobacco. In particular, it would be
highly desirable to provide a tobacco-containing smoking article, such as
an article having the general appearance of a cigarette, cigar, or pipe,
that possesses the ability to provide a smoker many of the benefits and
advantages of conventional tobacco smoking without necessarily
delivering considerable quantities of incomplete combustion and pyrolysis
products.”
69.
On a plain reading of para [0010], it is clear that problem of D1 was
never of igniting the smoking article when flame is applied. On perusal of
the summary and other disclosures in D1, I agree with the Controller and the
Patentee that D1 fails to disclose certain features of Claim 1 viz., aerosolforming substrate comprises a gathered sheet of aerosol-forming material;
and (b) thermally-conductive material, which acts as a thermally conducting
flame barrier for spreading heat and mitigates against the risk of a user
igniting the aerosol-forming substrate when flame is applied to the aerosolgenerating article. D1 has two separate ingredients i.e., ‘an aerosol-forming
material’ positioned within the outer housing, which is in fluid
communication with the ‘tobacco material’ [paras 0019 and 0020].
Reference of gathered sheet in D1 is in para [0089] as a web of
re-constituted tobacco sheet that is gathered so as to possess a plurality of
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
longitudinal extending passageways, [0089]. Appellant admits that D1 fails
to disclose explicitly a thermally-conducting material acting as a flame
barrier to spread heat and mitigate risk of igniting the substrate when flame
is applied and the contest is that this feature is a functional aspect of the
sheet and inherent to metal foil wrappers.
70.
Controller has rightly disagreed with the Appellant on this aspect and
observed that making of the heated aerosol-generating article using a
thermally-conducting sheet is in a way that it spreads heat, if unknowingly
flame is applied to the aerosol-generating article and Claim 1 is limited by
this feature as also that Appellant has not mapped the feature between the
granted patent and D1. There is merit in Patentee’s argument that where a
structural element is associated with a functional element, the latter limits
the claim to structures that are capable of performing that function. In the
instant case, the structural aspect is the wrapper with its feature of being
thermally-conductive and it limits the scope of Claim 1 by its functionality
of acting as a flame barrier. Controller has also compared the construction
and working of aerosol-generating article in D1 and Claim 1 of the patent.
Comparative table of Figures 2 and 3 are as follows:Figure 2 of Claim 1
Figure 3 of D1
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
71.
Perusal of Figure 2 of Claim 1 reflects that the four elements i.e.,
aerosol-forming substrate, hollow cellulose acetate tube, a spacer element
and a mouth piece filter are sequentially arranged in co-axial arrangement
and are assembled by a cigarette paper. The article has a mouth end which a
user inserts in his mouth during use and the thermally-conducting sheet
around aerosol-forming substrate at the distal end. The embodiment of
aerosol-generating article is suitable for use with electrically operated
aerosol-generating device comprising a heater for heating the aerosolforming substrate. The wrapping material in Figure 3 of D1 is very close to
the mouth piece and hence, no user will apply flame around the wrapping
material of D1, thus evidencing that the wrapper around the tobacco rod is
not for dissipating heat if ignited by a flame and it rather acts as a heat sink
to concentrate the heat into the tobacco rod for generating aerosol vapor.
72.
There are other significant differences in D1 and Claim 1 of the
patent. Para [0025] of D1 makes it clear that the aerosol-generating device
and the entire arrangement in D1 is complex and it uses three heating
elements to heat the tobacco rod whereas the heating element in the claimed
invention is only one. The arrangement of heating element in D1 is in a
tabular form which circumscribes the whole tobacco rod or part of it which
is not the feature of Claim 1. While para [0064] of D1 provides that the
substrate can be in the form of web or gathered sheet, as rightly flagged by
the Patentee, Appellant is unable to establish that it can be equated with the
gathered sheet in the claimed invention.
73.
Another significant difference is in the wrapper and this is one of the
bone of contentions between the parties. In D1 the wrapping material can be
a paper or metallic foil and para [0099] shows that the second heating
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
element heats the paper or the foil, as the case may be, to pass heat to the
tobacco, which then generates aerosol on being heated. The wrapper
therefore acts as a heat sink (medium) which passes the heat inside to the
substrate inside the tobacco rod and is meant to be in contact with the
heating element. Contrasted with this, the wrapper in Claim 1 is a heat
dissipator and acts as a thermally conducting flame barrier for spreading
heat and mitigating against the risk of user igniting the aerosol-forming
substrate, in the event the flame is applied inadvertently or accidently to the
aerosol-generating article and this is where the novelty resides.
74.
Patentee is right that Appellant’s understanding that flame barrier
properties are inherent in a laminate foil is not wholly sound. Controller’s
observations on the difference in a laminate foil and metal foil are
scientifically correct and based on very elementary knowledge in science.
Laminate is a fusion of layers of different metals and/or metal and paper etc.
and will have a different thermal-conductivity than a metal foil, whose
displayed properties will be those of the constituent metal. Controller has
correctly noted that D1 in para [0099] describes that wrapping material can
vary and can be a paper wrapping material of the type traditionally used for
cigarette manufacture or can be composed of a laminate of metallic foil and
paper. Indisputably, the wrapping material in D1 is designed to be in contact
with the heating element and para [0101] describes that the wrapping
material can be in electrical contact with electrical circuit associated with
electrical resistance heating element, which will provide heat to the tobacco
and in some embodiments of D1, wrapper is in direct contact with the third
heating element. It is in this backdrop, that the Controller observed that the
wrapping material in D1 can be a laminate and consequently, concluded that
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
it will have different thermal-conductivity as compared to wrapping material
in the opposed patent, which is a metal foil with a different thermalconductivity. If the very placement of wrapping material is such that there is
no scope of applying flame at that end, naturally the problem that D1
resolves has nothing to do with the feature in a wrapper that spreads heat
and mitigates against the risk of a user igniting the substrate, if flame is
applied to the aerosol generating article. Patentee does not claim the known
properties of a thermally-conducting wrapper and the novelty resides in
limiting the claim such that there is no ignition/combustion in the aerosolgenerating substrate when flame is applied to the aerosol-generating article
and therefore, the functional element serves as a screening assay. Even
during the hearing before this Court, Appellant has been unsuccessful in
traversing this fine and significant distinction between the granted Claim 1
and D1 and thus I find no infirmity in the view of the Controller that the
claimed invention in the granted patent is novel over prior art D1.
75.
The only other objection seriously pressed by the Appellant was lack
of inventive step/obviousness under Section 2(1)(ja) of 1970 Act. Before
proceeding to deal with the rival submissions, it will be useful to have a
quick look on the principles laid down from time to time for determining
inventive step or the lack thereof. Section 2(1)(ja) of the 1970 Act defines
‘inventive step’ as a feature of invention that involves technical advance as
compared to existing knowledge or having economic significance or both
that makes the invention not obvious to a person skilled in the art. In Avery
Dennison Corporation v. Controller of Patents and Designs, 2022 SCC
OnLine Del 3659, this Court referred to various approaches on this aspect
such as: problem/solution approach; could-would approach; and the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
teaching, suggestion and motivation approach, whereafter the Court looked
at the tests formulated by the House of Lords in Windsurfing International
Inc. v. Tabur Marine Ltd., [1985] RPC 59, as modified by the Court of
Appeals in Pozzoli SPA v. BDMO SA, [2006] EWHC 1398 (Ch), and I
quote:“1. Identifying the inventive concept embodied in the patent;
2. Imputing to a normally skilled but unimaginative addressee what was
common general knowledge in the art at the priority date;
3. Identifying the differences if any between the matter cited and the
alleged invention; and
4. Deciding whether those differences, viewed without any knowledge of
the alleged invention, constituted steps which would have been obvious to
the skilled man or whether they required any degree of invention.”
76.
Recently, the Division Bench of this Court in F.Hoffmann (Supra),
added another step and cumulatively, the five-steps which are a guiding light
for Controllers for determining inventive step are as follows:“Step No. 1 - To identify an ordinary person skilled in the art;
Step No. 2 - To identify the inventive concept embodied in the patent;
Step No. 3 - To impute to a normal skilled but unimaginative ordinary
person skilled in the art what was common general knowledge in the art at
the priority date;
Step No. 4 - To identify the differences, if any, between the matter cited
and the alleged invention and ascertain whether the differences are
ordinary application of law or involve various different steps requiring
multiple, theoretical and practical applications; and
Step No. 5 - To decide whether those differences, viewed in the knowledge
of alleged invention, constituted steps which would have been obvious to
the ordinary person skilled in the art and rule out hideside approach.”
77.
Coming back, Appellant cited prior arts D1-D6 as also D7-D10,
however, D7-D10 filed as additional documents under Rule 62(4) of 2003
Rules, were not considered by the Controller. Citing D1, Appellant argued
that the feature of the wrapper in Claim 1 of granted patent to act as a
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
thermally-conducting flame barrier and mitigate the risk of ignition or
combustion, is a functional aspect and an inherent property of the
wrapper/sheet material used and cannot impart or be qualified as a technical
advancement. Use of heat conductive material circumscribing a tobacco rod
will inevitably serve the purpose of dissipating heat and conducting it away
and thus, there resides no inventiveness in using a thermally-conductive
wrapper of metal foil once it is well known in the art that the property of
conducting heat is an inherent property of the metal foil. The claimed
invention is therefore at best a mere application of a known inherent
property of a thermally-conducting material. A skilled person in the art, in
view of D1 and the citations referred therein would be aware of the
properties of thermally-conductive materials such as metal foils and expect
them to act in a manner as claimed. Materials such as aluminium foils have
varied applications owing to the ability to spread and conduct heat and are
used in fire suits, chimneys etc. This position was seriously controverted by
the Patentee as captured in the impugned order and as referred to above.
Prior arts D2-D6 were also cited to bring home the point that the granted
claims lack inventive step.
78.
Opposition Board looked at prior arts D1-D6 and rendered a report in
favour of the Patentee recommending that subject matter of Claims 1-10 has
inventive step and thus Section 25(e) is inapplicable. The essential reasoning
in the recommendations is that D1 does not explicitly teach that gathered
tobacco sheet is folded/convoluted substantially and transversally to the
cylindrical axis of the rod. D1 teaches to assemble the aerosol-forming
substrate and at least one other element within the wrapper where the
wrapper is a laminate comprising metallic foil and paper and the foil only
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
transfers heat from the heating element to the tobacco and does not teach
that the wrapper is a thermally-conducting flame barrier.
79.
It was observed that D2 teaches about the wrapping material having
heat conductive properties and can comprise of metal or metal foil or
laminated material and that metal foil can conduct heat from the generating
segment to the aerosol-generating segment but fails to teach that the wrapper
sheet is made of thermally-conductive material, which acts as a flame barrier
for spreading heat and mitigating the risk of ignition, when flame is applied
to heated aerosol-generating article. D3 discloses a paper-aluminium foilpaper, which aids in minimizing any transfer of the aerosol-forming material
on the substrate to the fuel element, acting as an insulating jacket and/or
potentially staling of other components but fails to teach that the conducting
material acts as a flame barrier. Similarly, D4 also does not teach this feature
of the claimed invention albeit it teaches a smoking article comprising a
tobacco rod with a metallic foil subscribing a tobacco rod and a cylinder of
non-tobacco fuel surrounding the metal foil wrapper tobacco rod. The Board
further opined that D5 and D6 also do not teach the property of the wrapper
sheet to act as a flame barrier.
80.
Basis
the
respective
stands
of
the
parties
and
Board’s
recommendations, Controller concluded that Claim 1 of the subject patent
was inventive over prior arts D1-D6. Controller observed that a person
starting from the teachings of D1 and even combining them with those of
D2-D6 will not arrive at the claimed invention as none of them teach or
suggest: (a) aerosol-forming substrate comprises a gathered sheet of aerosolforming material; and (b) thermally-conducting material, which acts as a
thermally-conducting flame barrier for spreading heat and mitigating the risk
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
of user igniting the aerosol-forming substrate when flame is applied to the
aerosol-generating article. Relevant part of the order of the Controller is as
follows:“I state that D1 have been sufficiently discussed under head “Novelty”.
Now I will discuss arguments with respect to cited documents D2-D6 and
then combine these arguments with the disclosure of documents D1-D6 to
arrive at the question, whether the subject matter of granted claim 1 is
inventive or not.
For assessing inventive step, it is essential that invention as a whole
should considered. In other words, it is not sufficient to draw the
conclusion that a claimed invention is obvious merely because individual
parts of the claims taken separately are known or might be found to be
obvious. For the purpose of establishing obviousness of the invention to a
person skilled in the art, mosaicing multiple documents of prior arts is
permissible, if the cited prior art provides lead to the skilled person to
combine the teachings thereunder, at the time of filing or priority date of
patent application. (Manual of Patent office practice and procedure).
As described above under head novelty that D1 fails to disclose the
following features of claim 1 of the opposed patent.
1). aerosol-forming substrate comprises a gathered sheet of aerosolforming material; and
2). thermally-conductive material which acts as a thermally-conducting
flame barrier for spreading heat and mitigating against the risk of a user
igniting the aerosol-forming substrate by applying a flame to the aerosolgenerating article.
The Opponent in para 11.16 admits that:
a). D2 does not explicitly disclose that the smoking article is used with an
electrically operated smoking device and
b). the wrapper made of thermally-conductive material acts as a
thermally-conducting flame barrier for mitigating against risk of a user
igniting the aerosol-forming substrate.
As smoking article in D2 uses combustible heat source a person skilled in
the art will not have any incentive to combine the teachings of D2 with D1.
The smoking articles of D2 rely on the combustion of part of the article to
generate heat, they are clearly not adapted “for use with an electricallyoperated aerosol-generating device comprising a heating element”. For
these reasons, the skilled person would not consider D2 when seeking to
address the problem outlined above, which relates to improvements in
heated aerosol-generating articles.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
D2, in para [0024] discloses a representative wrapping material 58 for
the substrate material 55 can possess heat conductive properties, and can
have the form of a metal or metal foil (e.g., aluminium) tube, or a
laminated material having an outer surface comprised of paper and an
inner surface comprised of metal foil. The metal foil can conduct heat from
the heat generation segment 35 to the aerosol-generating segment 51. The
heat generation segment 35 includes a combustible heat source-40. (See
para [0019 of D2). Such a combustible heat source is not contemplated in
D1 and the skilled person would consequently not consider a wrapper
redistributing heat from a combustible heat source for applications where
the heat source is the heating element of an aerosol generating device as
in the case of D1.
Exhibit-3/D3
D3 is directed to improvements in fuel element compositions, whereby the
carbon monoxide generated during combustion of the fuel element is
reduced over previously known fuel compositions, and the fuel
composition affords reduced thermal energy output during smoking,
particularly during puffing, which in turn, reduces the carbon monoxide
(CO) levels produced during the burning of the fuel element and assists in
preventing the overheating of the smoking article or components thereof.
(See for example summary). D3 is not at all related to electrically
operated aerosol generating article rather D3 is concerned with reducing
the carbon monoxide generated during combustion of a fuel element
prepared from the composition. Therefore, a person skilled in the art will
not look up to D3.
The Opponent admits in para 11.22 of written statement of post-grant
opposition that the Opponent states that D3 does not explicitly disclose
that the smoking article is used with an electrically operated smoking
device. D3 relates to cigarettes in which ignition and combustion of part
of the cigarette is intended (specifically, combustion of fuel element 10).
So, D3 does not relate to the field of heated aerosol-generating articles”
within the meaning of claim 1.
Exhibit-4/D4
Similar to D3, D4 also relates to combustible heat source smoking article
having a cylindrical tobacco rod circumscribed by a metallic foil, a
cylinder of carbon fuel surrounding the wrapped tobacco rod, an air
permeable wrapper circumscribing the cylinder of carbon fuel, and a filter
plug coaxially located at one end of the tobacco rod and surrounding said
cylinder of carbon fuel. (See Summary of D4). In use of the smoking
article, the non-tobacco fuel cylinder combusts or burns and the heat from
the burning non-tobacco fuel cylinder is transferred through the foil metal
foil to the tobacco rod to heat the tobacco rod.
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
So, even D4 does not relate to the field of “heated aerosol-generating
articles” within the meaning of claim 1. It is important to note here that
the metallic foil is known and the claimed invention does not seek to get
patent protection on metallic foil. It is how it has made the aerosol
generating article with the use of thermally conducting material which
lower the propensity of ignition by redistributing the heat away from the
point where flame is applied and act as a barrier.
Exhibit-5/D5
D5 in para [0018] describes aerosol generating article that has diameter
of a conventional cigarette, includes a short, combustible carbonaceous
fuel element 10, an abutting aerosol generating means 12, and a foil lined
paper tube 14, which forms the mouth end piece 15 of the article. In this
embodiment, fuel element 10 is a "blowpipe" charcoal, i.e. carbonized
wood, which is provided with five longitudinally extending holes 16. See
Figure 1A. The fuel element 10, which is about 20 mm long, optionally
may be wrapped with cigarette paper to improve lighting of the charcoal
fuel. This paper may be treated with known burn additives.
Therefore, the smoking articles of D5 rely on the combustion of part of the
article to generate heat, they are clearly not adapted “for use with an
electrically-an operated aerosol-generating device comprising a heating
element”. For these reasons, the skilled person would not consider D5
when seeking to address the problem outlined above, which relates to
improvements in heated aerosol-generating articles.
Exhibit-6/D6:
The Opponent in para 11.32 of the written statement argues that D6
discloses use of sheet material as an outer wrapper for a heated smoking
article which comprises a heat source and an aerosol- generating
substrate. According to the Opponent, since the wrappers are sufficiently
heat resistant to withstand the heat generated by the heat source of such
smoking articles during use. D6 relates to smoking articles in which
ignition and combustion of part of the smoking article is intended
(specifically, combustion of combustible heat source 22). The combustible
heat source 22 is disclosed as being a pyrolysed porous carbon-based heat
source. So, D6 does not relate to the field of “heated aerosol-generating
articles” within the meaning of claim 1.
Therefore, a person starting from the teaching of document D1 and
combining the teachings of Documents D2-D6 would not arrive at the
claimed invention as none of these documents teaches or suggest the
following features of claim 1.
1). aerosol-forming substrate comprises a gathered sheet of aerosolforming material; and
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
2). thermally-conductive material which acts as a thermally-conducting
flame barrier for spreading heat and mitigating against the risk of a user
igniting the aerosol-forming substrate by applying a flame to the
aerosol-generating article.
In view of my above reasoning, I find claim 1 of the subject patent is
inventive over prior art D1 to D6. Therefore, the ground under Section
25(2)(e) is rejected.”
81.
Having examined the rival submissions and on perusal of the prior
arts as also granted claims, Court agrees with the patentee that D1 alone or
in combination with D2 to D10 does not make the granted invention
obvious. Under the head of novelty, Court has already returned a finding
that D1 fails to disclose or teach the feature “aerosol-forming substrate
comprises a gathered sheet of aerosol-forming material” circumscribed by a
wrapper. At best, D1 is a cigarette/cartridge having both tobacco and aerosol
as two separate segments within a single wrapper i.e. upstream segment
(tobacco) and downstream segment (aerosol-forming material). D1 also fails
to disclose the thermally-conductive material, which acts as a thermallyconducting flame barrier for spreading heat and mitigating against risk of a
user igniting the aerosol-forming substrate in the event flame is applied to
the aerosol-generating article. Moreover, the paper wrapper disclosed in D1
as a substitute/equivalent of a metallic wrap, would connote that the wrapper
is not meant to be a thermally-conducting flame barrier. Para [0099]
mentions that heat generated by second heating element can heat the
metallic foil laminates/wrapping material and hence the tobacco therein,
which means that the function of the wrapping material is to conduct heat
from the heating element to the tobacco rod and therefore, D1 teaches away
from the function of the wrapper in the granted claim. As stated in lines 6-7
of PCT publication, heated aerosol-generating article does not include a
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
combustible heat source. For ready reference, background section of
specification is as follows:
“BACKGROUND OF INVENTION
Aerosol-generating articles in which an aerosol-forming substrate,
such as a tobacco containing substrate, is heated rather than combusted
are known in the art. The aim of such heated aerosol-generating articles is
to reduce known harmful smoke constituents produced by the combustion
and pyrolytic degradation of tobacco in conventional cigarettes. A
conventional cigarette is lit when a user applies a flame to one end of the
cigarette and draws air through the other end. The localised heat provided
by the flame and the oxygen in the air drawn through the cigarette cause
the end of the cigarette to ignite, and the resulting combustion generates
an inhalable smoke. By contrast in heated aerosol-generating articles, an
inhalable aerosol is typically generated by the transfer of heat from a heat
source to a physically separate aerosol-forming substrate or material,
which may be located within, around or downstream of the heat source.
During consumption, volatile compounds are released from the aerosolforming substrate by heat transfer from the heat source and entrained in
air drawn through the aerosol-generating article. As the released
compounds cool, they condense to form an aerosol that is inhaled by the
consumer.
Heated aerosol-generating articles comprising tobacco for
generation of an aerosol by heating rather than burning are known in the
art. For example, WO2013/102614 discloses an aerosol-generating system
comprising a heated aerosol-generating article and an aerosol-generating
device having a heater for heating the heated aerosol-generating article to
produce an aerosol.
Tobacco used as part of an aerosol-forming substrate in heated
aerosol-generating articles is designed to produce an aerosol when heated
rather than when burned. Thus, such tobacco typically contains high levels
of aerosol formers, such as glycerine or propylene glycol. If a user were to
light a heated aerosol-generating article and smoke it as if it were a
conventional cigarette that user would not receive the intended user
experience. It would be desirable to produce a heated aerosol-generating
article that has a lowered propensity for flame ignition. Such a heated
aerosol-generating article would be preferably difficult to light during
attempts to light the article with a lighter, such as a flame, in the manner
of traditional cigarettes.”
82.
Summary section of the granted patent also states “the heated
aerosol-generating article is not an aerosol-generating article comprising a
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
combustible heat source”, which contrasts with conventional cigarettes,
which rely on ignition by application of flame. Importantly, the aerosolforming substrate in Claim 1 is radially encircled by a sheet of thermallyconductive material and is not heated through the wrapper, which
circumscribes the gathered sheet of aerosol-forming material. Para [0010] of
D1 contains the problem statement it tries to solve i.e. smoking articles that
employ tobacco substitute materials and smoking articles that employ
sources of heat other than burning tobacco cut filler to produce tobaccoflavoured vapours or tobacco-flavoured visible aerosol have not received
widespread commercial success. As rightly pointed out by the Patentee, the
problem of D1 was never to ignite the smoking article by someone
inadvertently or accidently applying flame to the aerosol-generating article.
Para [0025] of D1 discloses that smoking articles can further include a third
resistance heating element within the outer housing and are operatively
positioned to heat the tobacco rod and therefore, the whole arrangement uses
three heating elements to heat the tobacco rod in contrast to one heating
element in the opposed patent. The wrapper used in Claim 1 is a heat
dissipating device, which acts as thermally-conducting flame barrier, but the
wrapper in D1 is designed in a way that it acts as a heat sink (medium),
which passes heat inside the tobacco rod from the heating element of the
aerosol-generating device of D1 to generate aerosol. The wrapper is meant
to be in contact with the heating element whereas the wrapper around the
aerosol-forming substrate in Claim 1 is not in contact and serves the purpose
of a flame barrier mitigating the risk of ignition.
83.
Appellant’s argument on the difference in metal foil and laminate has
been discussed in the earlier part of the judgement. It may only be added that
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
Appellant is not correct in contending that the functional limitation of
providing a flame barrier against ignition due to flame application such as
when cigarette is lit, is not an inherent property of a laminate disclosed in
the prior art. No material was placed on record to establish this point. Also,
ignition temperature of the laminate foil is generally below flame
temperature of a conventional lighter or a matchstick used to light a cigarette
and is known to burn and/or melt if flame is applied. In my view, D1 fails to
disclose all features of Claim 1 including the specific wrapper and a person
skilled in the art will not be able to reach the granted invention from the
teachings of D1 and to this extent there is no infirmity in the view of the
Controller. Patentee also rightly claims that the technical advantages of the
granted invention are that avoiding combustion of the substrate may reduce
generation of various smooth constituents associated with combustion and
pyrolytic degradation of tobacco in conventional cigarettes as also that
aerosol-forming substrates designed for use in heated aerosol-forming
articles provide poor user experience if they are ignited rather than heated.
84.
Prior art D2 discloses numerous embodiments of smoking articles
falling into two groups. Figures 1, for reference has been extracted above.
The first group is in which a lighting end segment, heat generation segment
and aerosol-generating segment are successively, axially aligned relative to
each other and in the second group, the lighting end segment is omitted. D2
concerns rod shaped smoking articles comprising heat generation segment
(combustible fuel) and aerosol generating segment (glycerine and flavours),
which further incorporates a substrate material that acts as a carrier. D2
discloses a wrapping material possessing heat conducting properties and
being in the form of a metal or metal foil. Para 24 discloses that where the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
wrapping material includes a metal foil, the foil can conduct heat from the
heat generation segment to the aerosol generating segment to volatilise
aerosol forming components contained therein. Para 26 discloses that the
wrapping material can be adapted to facilitate the transfer of heat from the
heat generation segment to the aerosol generating segment and para 36
discloses that, in use, the smoking article is lit at the lighting end, using a
match or a cigarette lighter, in a similar manner in which a conventional
cigarette is lit. Para 36 specifically discloses that the smoking material of the
lighting and segment begins to burn when the user inhales the thermally
decomposed product. Para 37 discloses that burning of lighting end segment
causes the heat source of the heat generation segment to be heated, ignited
and burnt. Smoking articles rely on ignition and burning of substrate
material and are not heated aerosol generating articles as in Claim 1. For
this, reference be made to Para [0036] which reads: “During use, the smoker
lights the lighting end 14 of the smoking article 10 using a match or
cigarette lighter, in a manner similar to the way that conventional smoking
articles are lit.”
85.
Similarly, in the second group of smoking articles in D2, as evident
from Figure 7 above, the lighting end segment is absent. The heat generation
segment 35 forms the lighting end 14 and all the smoking articles rely on
ignition and combustion of part of the smoking article. Therefore, seen
holistically, D2 does not relate to the field of heated aerosol generating
articles within the meaning of Claim 1, as rightly put forth by the Patentee.
Moreover, since the smoking articles rely on combustion, they are not
adapted for use within an electrically operated aerosol generating device
comprising a heating element and it is thus unlikely that the skilled person
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
would consider D2 when seeking to address the problem at hand and/or
arrive at the invention as it does not belong to the field of “heated aerosolgenerating articles”. Controller has rightly observed and it is an admitted
position that D2 does not explicitly disclose that the smoking article is used
with an electrically operated smoking device or that the wrapper made of
thermally conductive material acts as a thermally conducting flame barrier
for mitigating against risk of a user igniting the aerosol forming substrate. It
is also rightly found that since the smoking article in D2 uses combustible
heat source, a person skilled in the art will not have any incentive to
combine the teachings of D2 with D1. The heat generation segment 35 in D2
includes a combustible heat source, which is not contemplated in D1 and
skilled person would not consider a wrapper redistributing heat from a
combustible heat source for application where the heat source is the heating
element of an aerosol generating device as in the case of D1.
86.
Prior art D3 also does not relate to the field of “heated aerosol-
generating articles” and relates to smoking articles (cigarettes) in which
ignition and combustion of part of the smoking article is intended and
required for use and operation of the smoking article. The smoking article
has a fuel element located at one end and a substrate containing one or more
aerosol forming material located downstream of the fuel element. It is
further disclosed that the barrier tube can be paper and metal foil laminate,
advantageously with the foil on the inside to assist in reducing or
eliminating any migration of the aerosol former from the substrate to other
components of the cigarette. It is further disclosed that paper wrapper
circumscribes the fuel element near the lighting end of the cigarette, with
wrapper 18 combined with the barrier tube 17 and preferably formed of
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
paper-aluminium foil-paper layers, to help minimize any transfer of aerosol
forming materials to the substrate 16 to the fuel element 10. D3 clearly
relates to cigarettes in which ignition and combustion of part of the cigarette
is intended and is thus not adapted for use with an electrically operated
aerosol-generating device comprising a heating element. There is no
teaching in D3 that the barrier tube or wrapper has the capacity to reduce
risk of ignition of the substrate in the event a flame is applied to the
cigarette.
87.
Consistent with D3 relying on combustion, presence of metal as part
of barrier tube wrapper does not prevent ignition of material enclosed
therein and only prevents excessive combustion. Clearly, the metal wrapper
in D3 is not configured to act as flame barrier and is directed to
improvement in fuel element compositions, as noted by the Controller,
whereby carbon monoxide generated during combustion is reduced over
previously known fuel compositions, which affords reduced thermal energy
output during smoking, particularly, during puffing, which in turn reduces
carbon monoxide levels and assists in preventing over heating of a smoking
article or a component thereof. Therefore, a person skilled in the art would
not use D3 as a starting point to arrive at the invention. Controller is right in
concluding that Claim 1 is inventive over D3. For ready reference, Figure 1
is extracted hereunder:-
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
88.
As for prior art D4, it relates to smoking article having a cylindrical
tobacco rod circumscribed by a metallic foil, a cylinder of carbon fuel
surrounding the wrapped tobacco rod, an air permeable wrapper and a filter
plug co-axially located at one end of the tobacco rod and surrounding the
carbon fuel cylinder. From the summary of D4, it is evident that while in
use, the non-tobacco fuel cylinder combusts or burns and the heat from the
burning non-tobacco fuel cylinder is transferred through the foil which is of
metal to the tobacco rod to heat the rod. Therefore, even D4 does not relate
to the field of heated aerosol-generating article and is concerned with
articles in which ignition and combustion of at least a part is intended.
Further, since reliance is on combustion to generate heat, the smoking
articles are not adapted for use with an electrically operated aerosolgenerating device comprising a heating element. The articles have a wrapper
formed of or including metal and are ignited and burnt during use and are
thus not configured to act as thermally-conducting flame barrier. The skilled
person would not use D4 to arrive at the invention and therefore, cannot be
an impediment to the inventiveness of Claim 1 of the granted patent.
89.
Prior art D5 also does not relate to the field of heated aerosol-
generating articles but relates to smoking articles in which ignition and
combustion at least of a part is intended. The smoking article has a
combustible carbonaceous fuel element, followed by an aerosol generating
means stop. The fuel element is made of charcoal and intended to be lit or
ignited. The aerosol generating means is in the form of glass beads coated
with an aerosol forming substrate, such as glycerine and the beads are
located between fuel element and a porous disc. An aerosol delivery passage
extends between the aerosol generating means and a mouth end of the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
article. A foil lined paper tube circumscribes part of fuel element and all the
aerosol generating means, porous disc and aerosol delivery passage. Lines 28 of D5 disclose that the foil lined tube increases heat transfer to the aerosol
generator and helps to extinguish the fire cone due to heat loss through the
foil. The aerosol generating article being reliant on combustion, is not
adapted for use with an electrically operated aerosol generating device,
comprising a heating element. There is no teaching in D5 of a foil lined tube
displaying properties of reducing risk of ignition of the aerosol-generating
means, in the event flame is applied to the smoking articles and instead
teaches use of a foil as part of the tube, which serves the purpose of
transferring heat. Controller rightly notes that para [0018] of D5 describes
aerosol-generating article that has diameter of a conventional cigarette with
a short, combustible carbonaceous fuel element, an abutting aerosolgenerating means and a foil lined paper tube. In this embodiment, fuel
element is a blowpipe charcoal, which is provided with extended holes and
the fuel element optionally may be wrapped with cigarette paper to improve
lighting of the charcoal fuel. This paper may be treated with known burn
additives and does not teach a skilled person to reach up to the invention
under the granted patent.
90.
Likewise, D6 relates to smoking article with a heat resistance sheet
material provided as an outer wrapper for a smoking article. None of the
articles of D6 are heated aerosol-generating articles and instead relate to
cigarettes in which ignition and combustion is intended. The combustible
heat source is disclosed as being a pyrolysed porous carbon-based heat
source, as given in Figure 2 and does not relate to the field of heated
aerosol-generating articles. The aerosol generating substrate 24 is disclosed
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
in the form of a longitudinally aligned filaments of extruded tobacco
material. The outer wrapper 30 is formed of a fibrous base layer 12 coated
with an inner layer 14 and an outer coating layer 16. The outer wrapper is
disclosed as being heat resistant and none of the materials disclosed even
remotely suggest that the wrapper is thermally conductive. A heat
conducting element in the form of a tube of aluminium foil surrounds and is
in contact with a rear portion of the combustible heat source 22 and a front
portion 24a of the aerosol generating substrate 24. For ready reference, the
figure is extracted hereunder:
91.
There is no teaching in D6 of the heat conducting element of
aluminium foil having a feature of reducing risk of ignition of aerosolgeneration substrate when flame is applied to the smoking article and at best
the heat conducting element may serve to transfer heat from combustion of
the heat source to aerosol-generating substrate and sans any teaching of the
wrapper being the sheet of thermally-conductive material acting as a flame
barrier for spreading heat and mitigating against ignition, it cannot be said
that a person skilled in the art would start with D6 in the context of the
granted invention. In light of the aforesaid teachings of prior arts D1-D6, it
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
cannot be urged by the Appellant that the Controller has erred in concluding
that Claim 1 of the subject patent is inventive over the said prior arts.
Therefore, there is also no merit in the contention of the Appellant that the
Controller has not followed the guidelines laid down in F.Hoffmann
(Supra), for determining the inventive step or lack thereof.
92.
Insofar as additional documents D7 to D10 are concerned, Controller
excluded them from consideration as being time barred under Rule 62(4) of
2003 Rules, relying on the judgement in Pharmacyclics LLC (supra). The
understanding of the Controller was that the deadline for filing the
publication is five days prior to the first scheduled date of hearing and not
adjourned date. In the instant case the first scheduled date of hearing was
30.04.2024 and the five days limit expired on 25.04.2024. D7-D10 were
filed on 31.05.2024 and hence, not accepted by the Controller. In para 40 of
the judgement in Pharmacyclics LLC (supra), on which reliance is placed
by the Controller and the Patentee, Court posed a question whether if a
hearing is adjourned, further evidence ought to be permitted, prior to the
next hearing and held that from the scheme of the 1970 Act it was clear that
filing of further evidence would not be permissible after first notice of
hearing and as per Rule 60, the hearing would be the first notice of hearing.
It was observed that this interpretation would ensure that parties do not
unduly delay the hearing of oppositions by seeking adjournments and
utilising the adjourned period to dig up more evidence, especially, when
such evidence has not been considered by the Opposition Board. Therefore,
as per this judgement the cut-off date for filing further evidence under
Rule 60 is the first scheduled date of hearing and the rationale is to ensure
that opposition proceedings are not unduly delayed, keeping in backdrop the
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
timeline for filing a post-grant opposition.
93.
There can be no quarrel on the point that post-grant oppositions must
be decided expeditiously and which is why timelines are provided in the
1970 Act and the Rules. However, it may not be right to hold that as a
matter of rule, publication can never be permitted under Rule 62(4) after the
first date of hearing. But an important caveat needs to be added that an
opponent cannot be granted adjournments and/or allowed to file publications
after the first date of hearing, as a matter of right and each case has to be
tested by the Controller on its own facts, keeping in mind the special
circumstances brought forth to seek leave to file the publications at that
stage, so as to curb any tendency of taking unnecessary adjustments and
prolonging the proceedings. In the instant case, first hearing notice was
issued on 13.02.2024 scheduling the hearing for 30.04.2024. At request of
the Appellant filed on 26.04.2024, the hearing was adjourned to 06.04.2024
and the publications being D7-D10 were filed on 31.05.2024. It cannot be
held in these facts that Appellant attempted to delay the proceedings.
Moreover, these are prior arts in the same field and it is therefore necessary
to consider them to determine if the patent was rightly granted. Considering
this is an appeal, Court has considered D7, which was the only additional
document, on which arguments were addressed on behalf of the parties.
94.
Document D7 relates to a non-combustion flavour inhalation article.
Appellant asserts that D7 makes the granted Claim 1 obvious to a person
skilled in the art, inasmuch as it relates to a heated aerosol-generating article
for use with an electrically operated aerosol-generating device. D7 also
teaches a roll including a tobacco sheet which is obtained by wrapping the
outside of the tobacco sheet shaped into a hollow cylindrical shape with a
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
heat conductive wrapping material, which is an aluminium foil or an
aluminium laminated paper. D7 as per the Appellant, teaches that the
wrapper can be a metal foil with high thermal conductivity and can avoid
combustion of tobacco sheet. It also teaches that aluminium foil has high
conductivity in the range of 236 W/m.K. A person skilled in the art knows
that
materials
with
high
thermal
conductivity
are
capable
of
spreading/conducting heat easily and are not easy to ignite as they have a
high ignition temperature due to high heat spreading/conduction capability
and therefore, it will be obvious to a skilled person in the art to use
metal/aluminium foil as a barrier configured to spread heat and avoid
ignition of the tobacco sheet for avoiding combustion. D7 also discloses
aerosol-forming substrate comprises tobacco sheet and para [0034] describes
wounded sheet of tobacco in multiple layers, which is equivalent to the
concept of gathered sheets. Thus, according to the Appellant, D7 explicitly
discloses most features of the impugned patent.
95.
D7 is a Japan Tobacco Patent Application titled “Non-combustion
flavour inhalation article” and was published on 11.08.2011. D7 expressly
discloses heated/non-combustion article having a tobacco sheet, metal foil
surrounding the tobacco sheet and a heating device. Potentially, D7 is
closest prior art having an aerosol-forming substrate and a sheet of
thermally-conductive material. However, there is a critical difference in D7
and Claim 1 of the granted patent. Claim 1 is not merely a combination of
tobacco sheet with metal foil and heater. The sheet of thermally-conductive
material, which acts as a thermally-conducting flame barrier for spreading
heat and mitigating against the risk of a user igniting the aerosol-forming
substrate by applying flame is the important feature in Claim 1. There is a
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
specific structural-functional relationship. D7’s principal teaching is a noncombustion flavour inhalation article and D7 clearly fails to teach that metal
foil surrounding the tobacco sheet and heated by a heater is a flame barrier,
intended to deal with a user applying flame to the article and configured for
spreading heat from such a flame, thereby intending to mitigate ignition of
the aerosol-forming substrate. In a nut shell, the distinction is very
instructive with regard to the wrapper acting as a flame barrier, spreading
heat from applied flame and mitigation of ignition in Claim 1 and therefore,
D7 does not anticipate the said claim.
96.
Structurally, D7 may be close to Claim 1, however, the stated
objective of D7 is to provide a non-combustion flavour inhalation article that
allows tobacco components/flavour to be inhaled without generating smoke
or combustion products and D7 achieves this objective by controlling the
heater temperature. Therefore, D7’s teaching is essentially to control the
electrical heater temperature so that the tobacco does not combust whereas
Claim 1 addresses a thermally-conductive wrapper acting as a flame barrier
spreading heat and mitigating ignition.
97.
D7 teaches that aluminium foil is used as heat-conductive wrapper,
which uniformly transfers controlled heat to tobacco sheet but does not
disclose the aluminium wrapper spreading heat laterally to reduce ignition of
tobacco sheet when external heat is applied, which is the relationship recited
in Claim 1. Appellant lays emphasis on the aluminium wrapper to bring
home the point that it has high thermal conductivity and thus not easy to
ignite and consequently, acts as a flame barrier. To my mind, these are two
separate problems. Firstly, thermal-conductivity may not be the same as
flame barrier behaviour of a wrapper, though they are related. Thermal
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
conductivity describes how readily heat travels through aluminium, which
has a high thermal conductivity of roughly 200-235 W/m.K. Flame barrier
behaviour describes how a material behaves when exposed to flame e.g.
whether it ignites, supports combustion, melts, shrinks etc. Aluminium foil
is itself non-combustible but because it is very thin, it can heat up rapidly
and may melt or lose its barrier function under sufficiently intense or long
flame exposure. D7 discloses that aluminium foil is conductive but that does
not establish that the foil is configured as a flame barrier or receives heat
from an externally applied flame and/or spreads that flame derived heat and
prevents a temperature rise in the tobacco substrate, thereby mitigating
ignition.
98.
Moreover, D7 appears to avoid combustion principally through
controlled heating below the relevant combustion/smoke generating
temperature, rather than by teaching an external flame protection
mechanism. Pithily put, the purpose of conductive wrapper in D7 is
“Uniform heat transfer” whereas in Claim 1 it is “Flame barrier/heat
spreading”. In D7, external flame contemplation is not identified whereas it
is expressly identified in Claim 1. The risk addressed in D7 is combustion
during heating while that in Claim 1 is ignition from user applied flame. In
fact, the argument of the Appellant is more in the nature of hindsight
reconstruction of the opposed patent, which is impermissible in law. It is
also to be noted that Appellant is unable to establish how the mere fact that
aluminium conducts heat is necessarily a motivation to use this feature for
specific problem of flame induced ignition. To sum up, D7 does not disclose
or render obvious the claimed flame barrier function and Appellant’s
reliance on D7 is based on impermissible conflation of thermal-conductivity
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
of aluminium with specific technical function required by Claim 1. While
disclosure of tobacco sheet surrounded by thermally-conductive wrapper
being aluminium foil is not disputed, however, importantly D7 fails to teach
that the wrapper material functions as thermally-conducting flame barrier for
spreading heat and mitigating against the risk of a user igniting the aerosolforming substrate by applying flame to the aerosol-generating article, as
expressly claimed in Claim 1 of the granted patent. Appellant’s leap from
aluminium’s thermal-conductivity to the claimed flame barrier function is in
fact an inference and not a disclosure and therefore, Appellant is not correct
in arguing that D7 anticipates Claim 1 of the granted patent.
99.
For all the aforesaid reasons, this Court is of the view that the
impugned orders both dated 30.01.2025 warrant no interference and
accordingly, the writ petition and the appeal are both dismissed. Pending
applications stand disposed of accordingly.
JYOTI SINGH, J.
SEPTEMBER 10 , 2026/S.Sharma/HS
Digitally Signed
By:KAMAL KUMAR
20:19:25
C.A.(COMM.IPD-PAT) 24/2025 & connected matter
This page is for informational and research purposes only and does not constitute legal advice.
Consult a qualified advocate for advice specific to your situation.
Is your name in this judgment and should it be masked, or is something on this page wrong?
Request a review